Numerical simulation analysis of large eddy simulation for T-tube based on solid-liquid two-phase abrasive flow

Jun Ye Li, Wen Qing Meng, Xiang Zang, Xinming ZhangVibroengineering 2017 · DOI

Abstract

Abrasive flow polishing technology is a critical nano-machining method for precision engineering. Large Eddy Simulation (LES) has emerged as a vital numerical method for studying the dynamics of abrasive grain polishing. This paper utilizes the FLUENT fluid mechanics software and the Mixture multiphase model to investigate the polishing process of T-tubes. Based on solid-liquid two-phase flow dynamics, the study discusses the micro-machining mechanisms and analyzes how varying inlet velocities influence the polishing effect by examining the resulting flow field characteristics.

Introduction

Precision machining of internal surfaces, particularly in complex geometries like T-tubes, presents a significant engineering challenge. Traditional mechanical polishing methods often fail to reach internal "nooks and crannies" effectively. Abrasive Flow Polishing (AFP)—a process where a pressurized, abrasive-filled fluid is pumped through a workpiece—offers a viable solution. However, the internal fluid dynamics remain a "black box." This study addresses the need to understand how fluid velocity and turbulence influence the polishing process, specifically focusing on how Silicon Carbide (SiC) abrasive grains interact with tube walls to ensure uniform finishing.

Methodology

The research utilized a numerical approach using FLUENT software, integrating two primary frameworks:

  1. Large Eddy Simulation (LES): Unlike standard RANS models that average turbulence, LES directly simulates large-scale turbulent structures. This is essential for capturing the complex "secondary flows" and vortices characteristic of T-junctions.
  2. Mixture Multiphase Model: The polishing medium, a solid-liquid slurry of oil and SiC particles, is treated as interpenetrating continua. This allows for tracking the volume fraction and velocity of the abrasive grains.
Mesh model of the T-tube used for Large Eddy Simulation.

The simulation model involved a T-tube with a 20mm inner diameter. Four inlet velocities were tested: 20, 30, 40, and 50 m/s. The liquid phase consisted of oil (Density: 1260 kg/m³, Dynamic Viscosity: 0.08 Pa·s), while the solid phase used Silicon Carbide particles (Density: 3100 kg/m³, Particle size: 30 μm).

Results and Discussion

The Double Vortex Phenomenon

A key finding is the emergence of a "double vortex" at the T-junction. As the abrasive flow encounters the intersection, centrifugal forces drive the fluid toward the outer wall. Due to incompressibility and pipe constraints, the fluid recirculates toward the center, creating a vortex. This phenomenon adds a tangential velocity component to the abrasive grains, causing them to "scrub" the wall in a circular motion rather than just impacting it head-on, which significantly enhances polishing effectiveness.

Impact of Inlet Velocity

The simulation results demonstrate a direct positive correlation between inlet velocity and polishing efficiency. As shown in the dynamic pressure contours, increasing the speed from 20 m/s to 50 m/s leads to a substantial increase in dynamic pressure and Turbulent Kinetic Energy (TKE) within the flow field.

Comparison of dynamic pressure distribution at inlet velocities of 20, 30, 40, and 50 m/s.

The highest dynamic pressure and TKE are concentrated at the intersection and the upper outlet. These "hot spots" experience the most intense grinding action. Furthermore, the grinding at the intersection creates a "fillet" (rounded corner), which helps reduce fatigue stress caused by high-pressure pulses during the tube's operational life.

Conclusion

This study confirms that higher inlet velocities in Abrasive Flow Polishing significantly boost efficiency by intensifying the dynamic pressure and creating complex vortex structures at tube intersections. While the numerical results provide a strong theoretical foundation, future work should address the upper limits of velocity beyond which processing quality might degrade and incorporate experimental validation to further refine the model.

Summary updated

Abstract

As a kind of nano machining technology, abrasive flow polishing technology plays an important role in precision machining region. As an important numerical simulation method in fluid mechanics, large eddy numerical simulation method has become an important method for many scholars to study abrasive grain polishing technology. In this paper, the use of fluid mechanics software FLUENT and selected Mixture mixed model. Based on the theory of solid-liquid two-phase flow dynamics, the large-eddy numerical simulation method was used to study the polishing process of T-tube abrasive flow, and the micro-machining mechanism of abrasive-polished workpiece was discussed. The influence of the different inlet velocities on the polishing effect of the abrasive grains was discussed by analyzing the numerical simulation results of the different inlet velocities of the abrasive grains during the processing of the T-tube.
BibTeX
@inproceedings{li2017numerical,
  author = {Jun Ye Li and Wen Qing Meng and Xiang Zang and Xinming Zhang},
  title = {{Numerical simulation analysis of large eddy simulation for T-tube based on solid-liquid two-phase abrasive flow}},
  booktitle = {Vibroengineering},
  year = {2017},
  doi = {10.21595/vp.2017.19027},
}
Figure