Numerical simulation analysis of four-step variable-diameter pipe by solid-liquid two-phase grinding

Jun Ye Li, Jing Lei Hu, Wen Qing Meng, Xiang Zang, Xinming ZhangVibroengineering 2017 · DOI

Abstract

This study investigates the behavior of solid-liquid two-phase abrasive flow within variable-diameter pipes to optimize internal surface polishing. Using a fourth-order variable-diameter pipe as a model, numerical simulations were conducted to analyze the distribution of dynamic pressure and turbulence intensity under varying inlet speeds. The results demonstrate that decreasing pipe diameter and increasing inlet velocity significantly enhance the polishing environment, providing a theoretical foundation for improving the efficiency and reliability of precision machining in complex internal geometries.

The Challenge of Internal Polishing

Internal surfaces of variable-diameter pipes—critical components in medical devices, fuel systems, and aerospace engineering—are notoriously difficult to polish. Traditional mechanical tools cannot easily reach or uniformly treat these changing geometries. Rough internal surfaces lead to increased friction, burrs, and reduced fatigue strength, which can cause premature part failure.

Abrasive Flow Machining (AFM) offers a solution by pumping a "liquid sandpaper" (a mixture of oil and abrasive grains) through the part. However, predicting how the flow behaves as it transitions through different diameters is complex. This paper seeks to provide a theoretical foundation for optimizing this process by simulating the physics of the flow field.

Simulation Methodology

The researchers performed numerical simulations using FLUENT software to model a four-step pipe with decreasing diameters: 1.2 mm, 1.0 mm, 0.8 mm, and 0.6 mm.

Diagram of the four-step variable-diameter pipe geometry used in the simulation.

Key technical details of the simulation include:

  • Solver: A 3D double solver utilizing the $k$-epsilon (2eqn) turbulence model.
  • Materials: A two-phase mixture of aviation hydraulic oil (liquid) and silicon carbide (solid) with a 0.2 volume fraction.
  • Boundary Conditions: Speed-inlet conditions (tested at 30, 40, 50, and 60 m/s) and non-slip wall boundaries.
  • Convergence: The model ran for 160 iterations to reach a stable state at an initial temperature of 300 K.

Key Insights and Results

The Compression Effect

As the abrasive flow moves from a larger diameter to a smaller one, the dynamic pressure undergoes a dramatic increase. The smallest section (the fourth-order area, 0.6 mm) experiences the highest pressure, suggesting that the most intense polishing occurs at the narrowest point of the pipe.

Contour plots showing the distribution of dynamic pressure across the four pipe sections at different inlet speeds.

Turbulence as a Polishing Tool

Increasing the inlet speed directly increases the turbulence intensity of the flow. This higher energy causes abrasive particles to strike the pipe walls more frequently and with greater force, which is the primary mechanism for material removal and surface smoothing.

Quantified results from the study include:

  • Dynamic Pressure Gains: At an inlet speed of 60 m/s, the dynamic pressure rose from 15.6 $\times 10^5$ MPa in the first (widest) section to 355 $\times 10^5$ MPa in the fourth (narrowest) section.
  • Energy Distribution: Turbulent kinetic energy (TKE) follows a parabolic distribution across the pipe's cross-section, peaking near the walls. This is ideal for polishing, as the energy is concentrated exactly where the work is required—on the internal surface.

Conclusion and Future Directions

The study confirms that the fourth-order area of a variable-diameter pipe consistently provides the most effective environment for high-precision grinding. While higher inlet speeds improve efficiency, there is a theoretical threshold where excessive speed could cause wear rather than refinement.

As this study is purely numerical, future work should focus on experimental validation by comparing these simulation clouds with actual surface roughness measurements from physically polished pipes. Additionally, investigating different transition angles (tapering) between steps could further optimize flow efficiency and material removal rates.

Summary updated

Abstract

In order to investigate the effect of abrasive flow on the polishing effect of variable diameter pipe parts, taking the fourth-order variable-diameter pipe part as the research object, the solid-liquid two-phase abrasive grains are used as the processing method of the fourth-order variable-diameter pipe, the numerical simulation of the machining process of the four-order variable-diameter pipe parts were carried out. Analysis of different inlet speed conditions, the dynamic pressure and the distribution of turbulence intensity of the flow field of the fourth order variable diameter pipe. Through comparative analysis, the effects of the four-stage variable-diameter pipe flow field are studied, which can provide the theoretical basis for the continuous improvement of the abrasive flow precision and ultra precision machining technology, which can improve the efficiency of abrasive flow processing, so that the workpiece fatigue strength is improved, enhance the reliability of the workpiece, extend the service life of the workpiece.
BibTeX
@inproceedings{li2017numerical,
  author = {Jun Ye Li and Jing Lei Hu and Wen Qing Meng and Xiang Zang and Xinming Zhang},
  title = {{Numerical simulation analysis of four-step variable-diameter pipe by solid-liquid two-phase grinding}},
  booktitle = {Vibroengineering},
  year = {2017},
  doi = {10.21595/vp.2017.19322},
}
Figure