Numerical Modeling on Assemble-type Composited Wall

Yuanyuan Zhao, Quan Yuan2016 · DOI

Abstract

A numerical modeling study was conducted using ABAQUS to perform push-over analysis on a novel assemble-type composited wall. The results demonstrated consistency with experimental data in terms of load-displacement curves and frame stress distribution. Furthermore, parametric simulations were performed to evaluate the influence of axial compression ratios, aspect ratios, and other key variables on the structure's stiffness, bearing capacity, and displacement ductility.

Introduction

The modern construction industry is increasingly moving toward modularization and prefabrication to address challenges such as high energy consumption, labor shortages, and extended project timelines. A promising innovation in this field is the assemble-type composited wall, which integrates a steel frame (comprising rib-beams and columns) with lightweight foam cement infill.

While these walls offer superior thermal insulation and assembly efficiency, their structural response—particularly their ultimate bearing capacity and seismic performance—is complex. Unlike traditional masonry or concrete walls, the interaction between the steel skeleton and the foam cement requires sophisticated modeling. This research aims to establish a reliable numerical simulation framework using ABAQUS to predict structural behavior, reducing the reliance on costly physical prototyping.

Numerical Modeling Methodology

The study utilized ABAQUS to perform nonlinear push-over analyses. The modeling approach focused on accurately representing the multi-material nature of the composite wall:

  • Element Selection: Steel reinforcement bars were modeled using T3D2 (3D linear 2-node) elements. The concrete frame and foam cement blocks were represented by C3D8R (8-node linear brick with reduced integration) elements, which are effective for capturing large deformations and contact interactions.
  • Interaction and Contact: A critical aspect of the model was the interface between the foam blocks, ribs, and the outer frame. The authors defined both normal and tangential contact properties. Specifically, the block and rib surfaces were designated as "dependent" and "master" surfaces, respectively, to simulate realistic load transfer and potential separation under stress.
Numerical model of the assemble-type composited wall showing boundary conditions and loading points.

Model Validation

To ensure the accuracy of the simulation, the numerical results were benchmarked against physical test data from a specimen designated as ECW-1. The primary metric for validation was the "skeleton curve," which plots the relationship between the applied lateral load and the resulting displacement.

The numerical skeleton curve closely matched the experimental results during the initial elastic phase. While slight deviations occurred during the elastic-plastic phase—likely due to idealized material assumptions in the software—the overall trend and ultimate capacity were well-captured. For a standard specimen, the ultimate load capacity was determined to be approximately 89.5 kN.

Comparison of load-displacement curves between experimental test results and numerical simulation.

Parametric Analysis and Key Insights

Following validation, a parametric study was conducted to understand how design variables affect performance:

1. Axial Compression Ratio

The study found a "sweet spot" for vertical loading. Initially, increasing the axial compression ratio improves performance as the vertical load "squeezes" the wall components together, constraining diagonal cracks and enhancing material cooperation. However, excessively high compression leads to a significant drop in ductility (the ability to deform without catastrophic failure), as materials reach their strain limits prematurely.

2. Aspect Ratio (Height-to-Width)

The geometry of the wall significantly dictates its failure mode. As the aspect ratio increases (taller, narrower walls), the failure mode shifts from "pure shear" to "shear-bending." While taller walls exhibit lower raw load-bearing capacity, they demonstrate improved displacement ductility, allowing them to sway more safely during seismic events. The ductility ratios ($\Delta_u/\Delta_y$) for the tested configurations ranged from 4.9 to 5.8, indicating robust seismic resilience.

Conclusion and Future Directions

The developed ABAQUS model provides a high-fidelity tool for predicting the performance of assemble-type composited walls. While the model slightly overestimates stiffness due to the omission of initial manufacturing imperfections and small gaps between blocks, it remains a powerful predictive instrument for engineering design.

Future research should aim to incorporate these initial imperfections and explore dynamic cyclic loading scenarios. Such studies would provide a more comprehensive understanding of how these modular walls behave under the back-and-forth oscillations characteristic of real-world earthquakes.

Summary updated

Abstract

A numerical modeling were built by ABAQUS to do push-over analysis, and the results were consistent with test results in load-displacement curve and frame stress nephogram. Furthermore, the influence of the changing key parameters were analyzed by numerical simulation to understand the axial compression ratio, the aspect ratio and other key parameters how to affect the structure's stiffness, bearing capacity and displacement ductility.
BibTeX
@misc{zhao2016numerical,
  author = {Yuanyuan Zhao and Quan Yuan},
  title = {{Numerical Modeling on Assemble-type Composited Wall}},
  year = {2016},
  doi = {10.2991/ifeesd-16.2016.30},
}
Figure