Numerical Analysis on the Effect of Artificial Ventilated Pipe Diameter on Hydrodynamic Performance of a Surface-Piercing Propeller

Zeyang Gao, Dongmei Yang, Ping Li, Yue DongJournal of Marine Science and Engineering 2019 · DOI

TL;DR

This paper investigates how the diameter of an artificial ventilation pipe affects the performance of surface-piercing propellers (SPPs) in high-speed crafts. Using CFD, they found that increasing the vent pipe diameter improves efficiency and reduces vibration, offering a practical method to enhance SPP performance in demanding conditions.

What Problem Does This Paper Address?

Surface-piercing propellers (SPPs) are favored for high-speed planning crafts due to their efficiency, cavitation elimination, and reduced appendage drag. However, under conditions of significant water immersion, SPPs can become heavily loaded, leading to reduced performance. A common solution is to install an artificial vent pipe in front of the propeller disc to introduce air, which mitigates some of these issues. While the general benefit of vent pipes is known, the specific impact of varying the vent pipe's diameter on the SPP's hydrodynamic performance, particularly in full immersion scenarios, remained less understood. This paper aims to fill that gap by numerically analyzing how different vent pipe diameters influence thrust, torque, efficiency, and vibration characteristics.

Methods

The researchers employed a Computational Fluid Dynamics (CFD) approach using the Finite Volume Method (FVM) and the commercial software Star-CCM+. They utilized a Reynolds-averaged Navier-Stokes (RANS) solver with the Shear Stress Transport (SST) k-ω turbulence model, which is known for its effectiveness in both far-field and near-wall regions. To handle the air-water interface, the Volume of Fluid (VOF) model was implemented, treating air and water as incompressible fluids.

A key aspect of their methodology was the use of an overlapping mesh technique to handle the relative motion between the stationary outer computational domain and the rotating inner domain containing the propeller. They also performed mesh independence and grid convergence studies to ensure the accuracy of their simulations, focusing on the Y+ value for near-wall grid quality. The study simulated a three-bladed surface-piercing propeller (SPP-1) under full immersion conditions, comparing four cases: a baseline without ventilation (P0) and three cases with ventilated pipes of increasing diameters (P1: 30mm, P2: 40mm, P3: 50mm).

Datasets

Not discussed in the paper. The study relies on numerical simulations and compares its results to existing experimental data from Ghassemi et al. [7] for validation purposes.

Key Insights and Ideas

  • Ventilation is key, but diameter matters: The study confirms that artificial ventilation significantly improves SPP performance, but the degree of improvement is directly linked to the vent pipe's diameter.
  • Efficiency gains with larger pipes: Increasing the vent pipe diameter leads to a rapid increase in propeller efficiency, a crucial factor for high-speed crafts.
  • Thrust and torque trade-off: While efficiency improves, thrust and torque coefficients generally decrease with larger vent pipe diameters, especially at lower advance speeds. This suggests a design optimization is needed to balance these factors.
  • Vibration reduction: Larger vent pipe diameters effectively reduce the peak of periodic vibrations in thrust and torque, leading to smoother operation.
  • Air cavity morphology: The study visually demonstrates how larger vent pipes create more continuous and stable air cavities, which positively impacts performance.

Key Results

  • Efficiency: The efficiency of the propeller (η) increases significantly with larger vent pipe diameters. For instance, at J=1.30, the efficiency for P3 (50mm) is notably higher than for P1 (30mm).
  • Thrust Coefficient (Kt) and Torque Coefficient (10Kq): Generally, Kt and 10Kq decrease as the vent pipe diameter increases, particularly at lower advance speed coefficients (J). For example, at J=0.85, P3 shows lower Kt and 10Kq than P0 (no ventilation). However, at higher advance speeds (J=1.30), this trend can reverse, with P3 sometimes showing slightly higher values than P1.
  • Vibration: The study shows that the pulsation characteristics (axial force, moment, lateral force, etc.) exhibit smaller undulation ranges for the largest vent pipe diameter (P3) compared to P1 and P2, indicating reduced vibration.
  • Air Cavity: Visualizations show that the 50mm vent pipe (P3) produces a continuous spiral air bubble and a centric air stream, whereas smaller pipes result in air bubbles breaking up more rapidly.

Limitations and Future Work

  • Full Immersion Focus: The study specifically investigates full immersion conditions. The behavior of SPPs with ventilated pipes under partial immersion, which is their typical operating mode, might differ and warrants further investigation.
  • Single Propeller Model: The analysis was conducted on a single SPP model (SPP-1). The generalizability of these findings to other SPP designs with different blade geometries or pitch ratios could be explored.
  • Experimental Validation: While the CFD results are compared to existing experimental data for validation, direct experimental validation of the ventilated pipe effects with varying diameters would strengthen the conclusions.
  • Optimization: The paper suggests that increasing vent pipe diameter has a positive effect on propulsion efficiency. Future work could focus on optimizing the vent pipe diameter for specific operating conditions or craft types to achieve the best balance between efficiency, thrust, and vibration. Investigating the influence of vent pipe placement and shape could also be valuable.

Summary updated

Abstract

Under the condition of large water immersion, surface-piercing propellers are inclined to be heavy loaded. In order to improve the hydrodynamic performance of the surface-piercing propeller, the installation of a vent pipe in front of a propeller disc is more widely used in the propulsion device of high speed planning crafts. Based on computational fluid dynamics (CFD) method, this paper studied the influence of diverse vent pipe diameters on hydrodynamic performance of the surface-piercing propeller under full water immersion conditions. The numerical results show that, with the increase of vent pipe diameters, the thrust and torque of the surface-piercing propeller decrease after ventilation, and the efficiency of the propeller increases rapidly; the low pressure area near the back root of the blade becomes smaller and smaller gradually; and the peak of periodic vibration of thrust and torque can be effectively reduced. The numerical results demonstrate that the installation of artificial vent pipe effectively improves the hydrodynamic performance of surface piercing propeller in the field of high speed crafts, and the increase of artificial vent pipe diameter plays an active role in the propulsion efficiency of the surface-piercing propeller.
BibTeX
@article{gao2019numerical,
  author = {Zeyang Gao and Dongmei Yang and Ping Li and Yue Dong},
  title = {{Numerical Analysis on the Effect of Artificial Ventilated Pipe Diameter on Hydrodynamic Performance of a Surface-Piercing Propeller}},
  journal = {Journal of Marine Science and Engineering},
  year = {2019},
  doi = {10.3390/jmse7080240},
}
Figure