Numerical analysis for viscosity temperature characteristics of abrasive flow finishing on micro-bore nozzle

Jun Ye Li, Xiang Zang, Wen Qing Meng, Xinming ZhangVibroengineering 2017 · DOI

Abstract

Abrasive Flow Machining (AFM) is an essential ultra-precision process for finishing micro-bore components like fuel injector nozzles. This study investigates the viscosity-temperature characteristics of AFM using numerical simulations. By employing FLUENT software with Mixed Phase and Discrete Phase Models (DPM), the researchers analyzed the solid-liquid two-phase flow field within a nozzle orifice. The findings reveal how field temperature and slurry viscosity influence particle erosion rates, providing a theoretical framework for optimizing industrial finishing parameters.

Introduction

As industrial components such as medical devices and micro-gears continue to shrink, traditional mechanical polishing becomes impractical. Abrasive Flow Machining (AFM) addresses this by forcing a pressurized, abrasive-laden slurry through the workpiece. However, the internal physics are complex; friction-generated heat alters the slurry's viscosity, which significantly impacts how abrasive particles interact with the internal walls. This paper seeks to model these dynamics to predict and improve finishing quality in micro-bore nozzles.

Methodology

The study utilized FLUENT software to simulate the fluid environment, guided by the governing equations of mass, momentum, and energy conservation.

Modeling Approach

  • Flow Dynamics: A Mixed Phase Model was used for bulk flow, while a Discrete Phase Model (DPM) tracked individual silicon carbide (SiC) particles.
  • Viscosity Function: Viscosity was modeled as temperature-dependent using an exponential function: $\mu = 0.131e^{-0.026t} \text{ Pa}\cdot\text{s}$.
  • Geometry: The simulation was based on a 3D fluid region model of a real-world servo valve nozzle.
3D fluid region model of the micro-bore nozzle used in the simulation

Results and Discussion

Pressure and Velocity Effects

The simulation identified that the highest static pressure occurs at the entrance of the processing channel, followed by a significant drop as the slurry enters the micro-bore. This pressure gradient is critical for transferring energy to the abrasive particles for "micro-grinding."

There is a direct positive correlation between inlet velocity and erosion intensity. As shown in the nephograms, increasing the velocity from 30 m/s to 60 m/s significantly enhances the dynamic pressure and the resulting erosion rate on the nozzle walls.

Static and dynamic pressure distribution nephograms at different inlet velocities (30–60 m/s)

Contrary to some expectations, higher slurry viscosity within the studied range actually improved the particle erosion rate by enhancing the "activity" and flowability of the medium. Similarly, increasing the temperature from 290 K to 320 K improved flowability and particle motion intensity. However, the authors caution that excessively high temperatures may eventually thin the fluid too much, reducing its ability to carry particle momentum effectively.

Conclusion

This numerical analysis demonstrates that both temperature and viscosity are pivotal levers in controlling the efficiency of Abrasive Flow Machining. By optimizing inlet velocity and maintaining slurry temperature within a specific range, manufacturers can significantly enhance the precision finishing of micro-bore components. Future work should focus on experimental validation to correlate these simulation results with physical wear measurements.

Summary updated

Abstract

Abrasive flow machining has become an efficient and economical ultra precision process for machining micro-bore parts. In this paper, aiming at viscosity temperature characteristics of abrasive flow finishing on micro-bore nozzle, under the guidance of the three governing equations of fluid mechanics theory, mixed phase model and discrete phase model were conducted, FLUENT software was resorted to simulate the discrete and fluid phase numerical characteristics of the solid-liquid two-phase flow field in the nozzle orifice with various field temperature and viscosity of slurry, the mechanism of erosion and wear of particles and effect of different processing parameters on particle erosion rate were uncovered, which provides a theoretical basis for the nozzle structure of abrasive flow machining.
BibTeX
@inproceedings{li2017numerical,
  author = {Jun Ye Li and Xiang Zang and Wen Qing Meng and Xinming Zhang},
  title = {{Numerical analysis for viscosity temperature characteristics of abrasive flow finishing on micro-bore nozzle}},
  booktitle = {Vibroengineering},
  year = {2017},
  doi = {10.21595/vp.2017.19028},
}
Figure