TL;DR
This paper reveals that water nanobridges, commonly found between surfaces in humid air, can cause significant "noncontact" friction. They demonstrate that this friction arises from the "pinning-depinning" dynamics of the water's contact line, leading to a novel form of nonviscous damping that can even dominate over traditional hydrodynamic friction.
What Problem Does This Paper Address?
Friction is a fundamental phenomenon, but understanding its microscopic origins, especially in ambient conditions, remains challenging. In dry environments, friction is largely attributed to the stick-slip dynamics of contacting asperities. However, in humid air, capillary forces from water nanobridges play a crucial role. While these bridges are known to increase friction by effectively adding to the normal load, their direct contribution to noncontact friction – friction occurring even when surfaces aren't directly touching – has been less understood. This is particularly important because the real contact area between surfaces is often much smaller than the apparent contact area, meaning these noncontact interactions mediated by nanobridges could significantly influence overall friction. This paper aims to elucidate the mechanism behind this noncontact friction generated by single capillary bridges.
Methods
The researchers employed a noncontact dynamic force spectroscopy (DFS) technique using a homebuilt atomic force microscope (AFM). This setup allowed for:
- Stable nanobridge formation: A quartz tuning fork oscillator with a stiff tip enabled controlled formation of capillary water nanobridges between a gold tip and a mica substrate, avoiding jump-to-contact instabilities common with softer AFM cantilevers.
- Sensitive force measurement: The system could simultaneously and separately measure the conservative (elastic) and non-conservative (damping) components of the tip-liquid interaction force.
- Controlled shear velocity: The DFS method allowed for measurements across a wide range of sliding velocities while maintaining a constant bridge volume.
- Quantitative analysis: The technique provided "effective" elastic ($k_{eff}$) and damping ($b_{eff,\omega}$) coefficients, allowing for quantitative analysis of the interaction forces.
The experimental data was then analyzed using theoretical models to understand the underlying physics of the capillary shear interaction.
Datasets
Not discussed in the paper. The study relies on experimental measurements obtained from the custom-built AFM setup.
Key Insights and Ideas
- Noncontact friction is real and significant: Even without direct contact, water nanobridges can generate substantial friction.
- Contact line dynamics are key: The friction isn't due to bulk water viscosity but rather the behavior of the water's three-phase contact line at the interface.
- "Nonviscous" damping: A novel damping mechanism, distinct from traditional hydrodynamic damping, arises from the molecular-scale "pinning-depinning" (or stick-slip) dynamics of the contact line.
- Logarithmic velocity dependence: This nonviscous damping leads to a logarithmic increase in friction force with sliding velocity, mirroring the behavior of dry contact friction.
- Humidity matters: The strength of this noncontact friction is strongly dependent on relative humidity, increasing significantly with higher humidity due to larger nanobridge formation.
Key Results
- The study successfully measured the elastic ($k_{eff}$) and damping ($b_{eff,\omega}$) coefficients of single capillary nanobridges.
- Hydrodynamic damping was found to be orders of magnitude smaller than the experimentally measured damping, ruling it out as the primary mechanism.
- A theoretical model based on contact line pinning-depinning dynamics accurately predicted the observed elastic and damping forces.
- The elastic force ($F_k$) was found to be proportional to the contact line radius ($R_l$), while the damping force ($F_b$) showed a logarithmic dependence on shear velocity.
- With increasing relative humidity from 2% to 60%, the noncontact sliding interaction force was enhanced by an order of magnitude. Specifically, at 60% RH, $k_{eff}$ and $b_{eff,\omega}$ were 5 and 10 times larger, respectively, than at 2% RH.
- The calculated complex shear modulus ($G^*$) for the nanobridge was found to be comparable to that of rubber, with the loss modulus ($G''$) being significantly larger than that of bulk water.
Limitations and Future Work
- Model Simplifications: The theoretical model for elasticity used a simplified cylindrical column approximation, and while it showed good qualitative agreement, quantitative discrepancies were noted, suggesting the need to consider more detailed bridge geometries.
- Continuum Assumption: The continuum material model for the liquid bridge might break down for very small contact line radii ($R_l < 15$ nm), where discrete atomic-scale effects become more important.
- Future Directions: The authors suggest that this noncontact friction mechanism could be responsible for observed logarithmic friction increases in some solid-solid contact experiments. Further research could explore the interplay between this noncontact friction and contact friction in more complex multi-asperity systems and investigate its role in the rheology of nanoscale interfacial fluids. The findings also have implications for designing and controlling micro/nano electro-mechanical systems.
Summary updated