New Process and Mechanism for Preparing Gradient Structural Aluminum Strip by Extrusion-machining

Wenjun Deng, Yuning Zeng, Zihan ZhouJournal of Mechanical Engineering 2022 · DOI

TL;DR

Researchers have developed a novel "one-step" manufacturing process called extrusion-machining to produce aluminum strips with a gradient microstructure. By combining the shearing action of cutting with the pressure of extrusion, they created materials that are nearly twice as strong as standard aluminum while retaining most of their ductility—effectively bypassing the traditional "strength-ductility trade-off."

What Problem Does This Paper Address?

In materials science, there is a classic dilemma: you can have a metal that is incredibly strong (usually by making its crystalline grains tiny, known as ultra-fine grains) or a metal that is very ductile (stretchy), but rarely both. Materials with a gradient structure—where the grain size changes gradually from the surface to the core—offer a solution. They mimic the "best of both worlds" by having a hard, strong exterior and a tough, ductile interior.

However, existing ways to make these materials, such as surface mechanical attrition treatment (SMAT) or rolling, are often slow, require multiple steps, or can only create a very thin gradient layer (a few hundred microns). The authors of this paper sought a more efficient, high-throughput method to produce bulk gradient strips in a single operation.

Methods

The authors introduced a process called Extrusion-Machining (EM). Imagine a tool peeling a layer off a block of metal (machining) but immediately forcing that "peel" through a narrow side channel (extrusion).

Key aspects of their approach include:

  • Material: 1060 industrial pure aluminum.
  • Experimental Setup: A custom-designed die made of Cr12MoV steel was used in a hydraulic press. They varied the "extrusion thickness" ($t_{ch}$) from 1.0 mm to 1.6 mm to see how it affected the final product.
  • Simulation: They used Finite Element Method (FEM) software (Deform-2D) to model the "Y-shaped" high-strain zones, stress distribution, and temperature changes during the process.
  • Characterization: The team used EBSD (Electron Backscatter Diffraction) and SEM (Scanning Electron Microscopy) to map grain sizes and performed Vickers hardness and tensile tests to measure mechanical performance.

Datasets

As this is an experimental mechanics paper, it does not use large-scale digital datasets. Instead, the "data" consists of:

  • Physical measurements of 1060 aluminum samples.
  • Numerical simulation results generated via the Deform-2D software using a power-law constitutive equation for the material's flow stress.

Key Insights and Ideas

  • The "Y-Shaped" Strain Zone: The simulation revealed that the die geometry creates a unique "Y" pattern of high strain rates. This is the "engine" of the gradient: the side of the strip touching the tool edge undergoes massive deformation (high strain), while the opposite side undergoes much less.
  • Tunable Gradients: By simply changing the thickness of the extrusion channel, the researchers could "tune" the material. A thinner channel creates a more intense, uniform strain, while a thicker channel allows for a wider "low-strain" zone, resulting in a more pronounced gradient.
  • One-Step Efficiency: Unlike traditional methods that require treating a pre-made sheet, EM creates the strip and the gradient microstructure simultaneously from a bulk block.
  • Hardness-Strain Correlation: The researchers found a near-perfect match between the simulated strain maps, the observed grain refinement, and the measured hardness. This confirms that the process is highly predictable and controllable.

Key Results

  • Doubled Strength: The gradient aluminum strips achieved a tensile strength of up to 173 MPa, nearly double the 79 MPa of the original unprocessed aluminum.
  • Maintained Ductility: While strength doubled, the elongation (stretchability) only dropped from 27% to about 16.4%–22.9%. In the world of high-strength metals, this is a remarkably small sacrifice.
  • Microscopic Refinement: On the high-strain side (Side B), grains were refined down to approximately 0.55 μm (ultra-fine grains). On the low-strain side (Side A), grains remained much larger (around 4.39 μm).
  • Hardness Gradient: Hardness peaked at the surface (Side B) at ~54 HV and gradually decreased across the thickness, significantly higher than the base material's 32 HV.

Limitations and Future Work

While the results are promising, the authors noted a few hurdles:

  • Surface Defects: Periodic "micro-cracks" were observed on the side of the strip that faced the channel wall (Side A). This was attributed to high friction and the material being "obstructed" as it moved through the die.
  • Material Scope: This study focused exclusively on 1060 Aluminum. Future research is needed to see if this process works as effectively for harder alloys or different metals like copper or titanium.
  • Scaling: The experiments used small, non-standard tensile specimens. Moving this to an industrial scale where wide sheets are produced would require significant engineering of the die and press systems.

Summary updated

BibTeX
@article{deng2022new,
  author = {Wenjun Deng and Yuning Zeng and Zihan Zhou},
  title = {{New Process and Mechanism for Preparing Gradient Structural Aluminum Strip by Extrusion-machining}},
  journal = {Journal of Mechanical Engineering},
  year = {2022},
  doi = {10.3901/jme.2022.05.278},
}
Figure