Native Surface Oxides Featured Liquid Metals for Printable Self-Powered Photoelectrochemical Device

Yuqing Wang, Yaqi Li, Jingwei Zhang, Jincheng Zhuang, Long Ren, Yi DuFrontiers in Chemistry 2019 · DOI

TL;DR

This paper presents a novel, low-cost method for creating self-powered photoelectrochemical (PEC) devices by directly printing liquid metal (Galinstan) and utilizing its naturally formed oxide layer as the photoactive component. This approach overcomes challenges in integrating nanomaterials into electronic devices, offering a flexible and scalable platform for printable photodetectors.

What Problem Does This Paper Address?

Photoelectrochemical (PEC) devices are promising for converting light into electricity or chemical fuels. A key challenge in their development is the efficient and stable integration of photoactive semiconducting nanomaterials into functional devices. Traditional methods often involve complex fabrication processes, risk increasing electrical resistance, or hinder material utilization. This paper tackles the difficulty of creating stable, high-performance photoelectrodes by proposing a simple, direct-write method that leverages the inherent properties of liquid metals.

Methods

The core innovation lies in a facile manufacturing strategy that utilizes Gallium-based liquid metal (Galinstan) as both the conductive electrode and the precursor for a photoactive material.

  • Printing: Galinstan was printed into desired patterns on a flexible silicone rubber (PDMS) substrate using a layered molding and casting process. This allows for rapid and precise fabrication of electrode structures at room temperature.
  • Native Oxide Formation: Upon exposure to oxygen at room temperature, Galinstan rapidly forms a thin, 2D layer of gallium oxide (Ga₂O₃). This native oxide layer acts as the photoactive semiconductor.
  • Device Assembly: The printed Galinstan pattern served as the working electrode. A platinum (Pt) electrode was deposited as the counter electrode. A neutral solid-state electrolyte, composed of polyvinyl alcohol (PVA) and sodium chloride (NaCl) in deionized water, was used to bridge the electrodes. A final thin layer of PDMS was applied to encapsulate the device.
  • Characterization: A suite of techniques was employed to analyze the materials and device performance:
  • Optical microscopy and Scanning Electron Microscopy (SEM) with Energy Dispersive X-ray (EDX) spectroscopy were used to examine the printed patterns and elemental distribution.
  • Transmission Electron Microscopy (TEM) and Selected Area Electron Diffraction (SAED) were used to characterize the morphology and crystal structure of the Ga-oxide nanosheets.
  • X-ray Diffraction (XRD) was used to confirm the crystal structure of the printed Galinstan.
  • UV-Vis absorption spectroscopy was used to determine the optical properties and bandgap of the Ga-oxide.
  • Electrochemical measurements using a standard workstation (CHI660D) were performed to evaluate the photo-response, including linear sweep voltammetry (LSV) and current-time (i-t) measurements under simulated sunlight.

Datasets

Not discussed in the paper. The study focuses on the fabrication and characterization of a novel device rather than training on large datasets.

Key Insights and Ideas

  • In-situ Oxide Formation: The spontaneous formation of a Ga₂O₃ layer on liquid metal surfaces is a key enabler. This eliminates the need for separate, complex semiconductor synthesis and deposition steps.
  • Printable, Flexible Electronics: The use of liquid metal and PDMS allows for the fabrication of flexible and printable PEC devices, opening doors for applications on non-planar or deformable surfaces.
  • Self-Powered Operation: The developed PEC device exhibits self-powered photo-detection capabilities, meaning it can generate a signal in response to light without an external power source, even at low light intensities.
  • P-type Semiconductor Behavior: The native Ga-oxide layer was identified as a p-type semiconductor, which is crucial for understanding its photo-response mechanism and device performance.
  • Efficient Charge Transfer: The direct contact between the conductive liquid metal and the semiconducting oxide layer facilitates efficient charge carrier migration, minimizing series resistance.

Key Results

  • Printable Patterns: Defined patterns of Galinstan were successfully printed on PDMS substrates, demonstrating high electrical conductivity.
  • Ga-Oxide Characterization: TEM revealed thin (~3 nm) Ga-oxide nanosheets with creases and folds. SAED and XRD confirmed the presence of hexagonal α-Ga₂O₃. The optical bandgap was determined to be approximately 4.75 eV.
  • Photo-Response: The PEC device showed a clear photo-response to simulated sunlight.
  • Under a 100 mW/cm² light intensity, the device exhibited a negative photocurrent density of approximately 80 nA/cm² and a photo-response rate faster than 0.1 s, even at 0 V bias.
  • The device demonstrated a linear increase in photocurrent density with increasing light intensity from 20 to 100 mW/cm².
  • The calculated responsivity varied from 2 to 1 µA/W, indicating good sensitivity compared to other similar devices.

Limitations and Future Work

  • Oxide Thickness Control: While the native oxide layer is beneficial, controlling its precise thickness and uniformity across larger areas might be a challenge for optimizing performance.
  • Electrolyte Stability: The use of a PVA-NaCl electrolyte, while functional, could be further improved for long-term stability and wider operating conditions.
  • Future Directions: The authors suggest that this novel design provides a promising platform for developing practical printable photodetectors and for manufacturing more complex and soft PEC devices or semiconductor-based photo-electronics. Further exploration into different liquid metal alloys and oxide compositions could lead to enhanced performance and new functionalities.

Summary updated

Abstract

Constructing high-performance photo-electrodes by patterning the photo-active semiconducting components with desirable texture and architecture is one of the most promising approaches to achieve the practical and scale-up application of photo-electric or photoelectrochemical (PEC) devices. However, it is a still big challenge to efficiently and effectively handle nano-structural semiconducting materials into intergraded circuit devices, displaying good electric-contact and stability. Here, a facile manufacture strategy for fabricating native metal-oxides based photo-electrodes by directly printing Ga-based liquid metals is explored. The PEC device, functionalized by the native Ga-oxide functional layer, exhibits self-powered photo-detection behaviors and presents fast photo-electric responsibility in response to the simulated Sunlight illumination. This printable PEC device shows good potential for high sensitive self-powered photo-detector and provides a flexible and versatile approach for the design and fabrication of novel electrode structures.
BibTeX
@inproceedings{wang2019native,
  author = {Yuqing Wang and Yaqi Li and Jingwei Zhang and Jincheng Zhuang and Long Ren and Yi Du},
  title = {{Native Surface Oxides Featured Liquid Metals for Printable Self-Powered Photoelectrochemical Device}},
  booktitle = {Frontiers in Chemistry},
  year = {2019},
  doi = {10.3389/fchem.2019.00356},
}
Figure