N and OH-Immobilized Cu3 Clusters In Situ Reconstructed from Single-Metal Sites for Efficient CO2 Electromethanation in Bicontinuous Mesochannels

Fuping Pan, Lingzhe Fang, Boyang Li, Xiaoxuan Yang, Thomas O’Carroll, Haoyang Li, Tao Li, Guofeng Wang, Kai‐Jie Chen, Gang WuJournal of the American Chemical Society 2024 · DOI

TL;DR

Researchers have achieved a breakthrough in CO₂ electromethanation by combining atomic-scale catalyst engineering with mesoscale "microenvironment" design. By using a block copolymer to create a carbon support with interconnected, long-range mesochannels, they successfully trapped reaction intermediates and excluded water, resulting in a record-breaking 74.2% Faradaic efficiency for methane at industry-level current densities.

What Problem Does This Paper Address?

Converting CO₂ into useful fuels like methane (CH₄) using renewable electricity is a "holy grail" of green chemistry. However, the CO₂ reduction reaction (CO₂RR) is notoriously difficult to control.

Two major hurdles stand in the way:

  1. The Hydrogen Competition: In the aqueous environments required for these reactions, it is much easier for electricity to split water into hydrogen gas (the Hydrogen Evolution Reaction, or HER) than it is to reduce CO₂.
  2. Selectivity Chaos: Even when CO₂ is reduced, Copper (the go-to catalyst) often produces a mixture of products, including carbon monoxide, ethylene, and ethanol. Steering the reaction specifically toward methane—which requires a complex eight-proton/electron transfer—is incredibly challenging.

The authors argue that we cannot just look at the catalyst atoms; we must also engineer the "local microenvironment"—the tiny neighborhood of pores and channels where the reaction actually happens.

Methods

The team developed a dual-pronged strategy:

  • Mesoscale Engineering (The Support): They used a block copolymer (PAN-b-PMMA) to create Interconnected Mesoporous Carbon Fibers (IPCF). Unlike standard carbon supports with dead-end or short pores, the IPCF features long, "bicontinuous" mesochannels. These channels were synthesized via electrospinning and controlled "microphase separation," where the PMMA acts as a removable template to leave behind a network of uniform pores (~9.3 nm).
  • Atomic-Scale Engineering (The Active Site): They started with atomically dispersed Copper (single atoms) coordinated with Nitrogen (Cu-N₃).
  • In-Situ Observation: Crucially, the researchers didn't just look at the catalyst before and after the reaction. They used in-situ X-ray Absorption Spectroscopy (XAS) and Raman spectroscopy to watch the catalyst in real-time under operating conditions.
  • Theoretical Modeling: Density Functional Theory (DFT) calculations were used to map the energy barriers of the reaction pathways on the reconstructed sites.

Datasets

As a materials science paper, the "datasets" consist of experimental characterization and performance benchmarks:

  • Morphology Data: SEM, TEM, and HAADF-STEM imaging to confirm the pore structure and atomic dispersion.
  • Adsorption Isotherms: N₂ and CO₂ gas adsorption data to quantify surface area and pore volume.
  • Electrochemical Performance: Faradaic efficiency (FE) and partial current densities measured across a range of potentials (-0.8V to -1.6V vs. RHE).
  • Comparative Benchmarking: The IPCF catalyst was compared against two controls: mesopore-deficient carbon (CF) and discontinuous porous carbon (PCF), as well as a comprehensive list of previously reported Cu-based catalysts in the literature.

Key Insights and Ideas

  • The "Aha" Moment: In-Situ Reconstruction. The most surprising finding was that the "single-atom" Cu-N₃ sites are not the actual catalysts. Under the negative potential of the reaction, these single atoms migrate and cluster into N,OH-immobilized Cu₃ clusters. Once the power is turned off, they revert back to single atoms. This dynamic "reconstruction" is what actually drives the methane production.
  • The Power of Confinement: The long-range mesochannels act like tiny chemical reactors. They are hydrophobic enough to keep bulk water out (starving the competing HER) but long enough to increase the "residence time" of CO intermediates. This forces the CO to stay in contact with the Copper sites longer, pushing the reduction all the way to methane.
  • Selectivity by Design: DFT calculations revealed that the Cu₃ clusters have a very low energy barrier for turning CO into CHO (the path to methane) but a very high barrier for C-C coupling (the path to ethylene). This explains why the catalyst is so "intrinsically selective" for methane.

Key Results

  • Record Efficiency: The Cu-N/IPCF catalyst achieved a 74.2% Faradaic efficiency for methane.
  • High Throughput: This was achieved at a current density of 300 mA cm⁻², which is considered the threshold for industrial viability.
  • Partial Current Density: The specific current dedicated to methane production reached 222.6 mA cm⁻², placing it at the top tier of reported Cu-based catalysts.
  • Suppression of HER: The interconnected pore structure significantly reduced hydrogen production compared to standard carbon supports, proving the "microenvironment" theory.

Limitations and Future Work

While the results are impressive, the authors note a few areas for improvement:

  • Long-term Stability: The catalyst was tested for 3 hours. While it remained relatively stable, there was a slight decline in methane efficiency toward the end, likely due to the gas diffusion electrode (GDE) losing its hydrophobicity over time.
  • Industrial Scaling: Moving from a lab-scale flow cell to a full-scale industrial electrolyzer will require further optimization of the electrode's physical durability.
  • Economic Threshold: The paper acknowledges that while this is a "top level" performance, further improvements are needed to reach the absolute economic threshold for profitable, electricity-powered CO₂-to-methane conversion.

Summary updated

Abstract

Cu-based catalysts hold promise for electrifying CO<sub>2</sub> to produce methane, an extensively used fuel. However, the activity and selectivity remain insufficient due to the lack of catalyst design principles to steer complex CO<sub>2</sub> reduction pathways. Herein, we develop a concept to design carbon-supported Cu catalysts by regulating Cu active sites' atomic-scale structures and engineering the carbon support's mesoscale architecture. This aims to provide a favorable local reaction microenvironment for a selective CO<sub>2</sub> reduction pathway to methane. In situ X-ray absorption and Raman spectroscopy analyses reveal the dynamic reconstruction of nitrogen and hydroxyl-immobilized Cu<sub>3</sub> (N,OH-Cu<sub>3</sub>) clusters derived from atomically dispersed Cu-N<sub>3</sub> sites under realistic CO<sub>2</sub> reduction conditions. The N,OH-Cu<sub>3</sub> sites possess moderate *CO adsorption affinity and a low barrier for *CO hydrogenation, enabling intrinsically selective CO<sub>2</sub>-to-CH<sub>4</sub> reduction compared to the C-C coupling with a high energy barrier. Importantly, a <i>block</i> copolymer-derived carbon fiber support with interconnected mesopores is constructed. The unique long-range mesochannels offer an H<sub>2</sub>O-deficient microenvironment and prolong the transport path for the CO intermediate, which could suppress the hydrogen evolution reaction and favor deep CO<sub>2</sub> reduction toward methane formation. Thus, the newly developed catalyst consisting of in situ constructed N,OH-Cu<sub>3</sub> active sites embedded into bicontinuous carbon mesochannels achieved an unprecedented Faradaic efficiency of 74.2% for the CO<sub>2</sub> reduction to methane at an industry-level current density of 300 mA cm<sup>-2</sup>. This work explores effective concepts for steering desirable reaction pathways in complex interfacial catalytic systems via modulating active site structures at the atomic level and engineering pore architectures of supports on the mesoscale to create favorable microenvironments.
BibTeX
@article{pan2024n,
  author = {Fuping Pan and Lingzhe Fang and Boyang Li and Xiaoxuan Yang and Thomas O’Carroll and Haoyang Li and Tao Li and Guofeng Wang and Kai‐Jie Chen and Gang Wu},
  title = {{N and OH-Immobilized Cu<sub>3</sub> Clusters In Situ Reconstructed from Single-Metal Sites for Efficient CO<sub>2</sub> Electromethanation in Bicontinuous Mesochannels}},
  journal = {Journal of the American Chemical Society},
  year = {2024},
  doi = {10.1021/jacs.3c10524},
}
Figure