Multilayer Black Phosphorus Near-Infrared Photodetectors

Chaojian Hou, Lijun Yang, Bo Li, Qihan Zhang, Yuefeng Li, Qiuyang Yue, Yang Wang, Zhan Yang, Lixin Dong2018 · DOI

TL;DR

This paper explores the potential of thicker multilayer black phosphorus (BP) flakes for near-infrared (NIR) photodetectors. They demonstrate that thicker BP flakes, contrary to some prior assumptions, can achieve high responsivity (up to 2.42 A/W) and fast photo-switching speeds (~2.5 ms), making them promising candidates for advanced optoelectronic devices.

What Problem Does This Paper Address?

Black phosphorus (BP) has emerged as a highly promising material for photodetectors due to its excellent optoelectronic properties, including broadband photo-response and high carrier mobility. However, most research has focused on monolayer or few-layer BP. These ultrathin flakes face challenges with environmental instability, and their potential for high-performance photodetectors, especially in the near-infrared (NIR) spectrum, remains underexplored. This paper addresses the gap in understanding the performance of thicker multilayer BP nanoflakes for NIR photodetection, investigating whether their potentially different electronic transport properties and improved stability translate into superior photodetector performance.

Methods

The researchers fabricated field-effect transistors (FETs) using multilayer BP nanoflakes with varying thicknesses (28 nm, 47 nm, and 302 nm). They employed an "all-dry transfer technique" using polydimethylsiloxane (PDMS) to transfer BP flakes onto a silicon substrate. Device fabrication involved standard e-beam lithography for patterning source/drain electrodes, followed by thermal evaporation of gold and a lift-off process.

Key characterization techniques included:

  • Atomic Force Microscopy (AFM) and Scanning Electron Microscopy (SEM) for structural analysis and thickness measurement.
  • Raman Spectroscopy to confirm the presence and quality of BP.
  • Agilent B1500A semiconductor parameter analyzer for electrical transport measurements (output and transfer characteristics) in the dark.
  • Near-infrared laser irradiation (830 nm) to study optoelectronic performance, measuring responsivity, photo-gain, photo-switching time, noise equivalent power (NEP), and specific detectivity (D*).

Datasets

Not discussed in the paper. The study relies on experimental measurements from fabricated devices.

Key Insights and Ideas

  • Thickness Matters for Transport: The study reveals that the current intensity in BP FETs initially increases with thickness up to around 47 nm, then slightly decreases for much thicker flakes (302 nm). This is attributed to a balance between screening effects in thinner flakes and interlayer conductivity in thicker ones.
  • Degenerate p-type BP is Beneficial: The research suggests that degenerated p-type BP, particularly in thicker flakes, is beneficial for achieving higher current intensity.
  • Thicker BP Excels in NIR Detection: Contrary to a potential assumption that thinner is always better for speed, thicker BP nanoflakes (302 nm) demonstrated a significantly higher responsivity (up to 2.42 A/W) compared to few-layer devices, while maintaining a fast photo-switching speed (~2.5 ms).
  • Environmental Stability Advantage: The paper highlights that thicker BP flakes, with their oxidized surface layer acting as native capping, offer better protection against water and degradation, potentially leading to longer device lifetimes.
  • High EQE Explained: The observed high external quantum efficiency (EQE) is attributed to multi-carrier generation, where the photon energy is significantly larger than the BP bandgap.

Key Results

  • Responsivity: Maximum responsivity achieved was 2.42 A/W for thicker BP photodetectors, which is substantially higher than reported values for 8-nm BP photodetectors (0.1 mA/W).
  • Photo-switching Speed: Rise time was measured at 2.5 ms, and fall time at 3.8 ms under moderate bias conditions, demonstrating remarkable speed.
  • Noise Equivalent Power (NEP): 6.8 × 10⁻¹¹ W/(cm·Hz)¹/², indicating good sensitivity.
  • Specific Detectivity (D*): 1.833 × 10⁸ cm·Hz¹/²/W, which is comparable to other materials but suggests room for improvement.
  • Thickness-dependent current: Current intensity increased up to ~47 nm and then slightly decreased for 302 nm thickness.

Limitations and Future Work

  • Specific Detectivity Improvement: While the NEP indicates good sensitivity, the authors acknowledge that the specific detectivity (D*) of their thicker BP photodetector could be further improved for ultra-sensitive applications.
  • Mechanism of Photoresponse: The paper suggests that the photoresponse in thicker BP is dominated by thermoelectric and bolometric processes, especially under low bias. Further investigation into these mechanisms could lead to optimized device design.
  • Optimization of Thickness: While 302 nm showed promising results, the study indicates an optimal thickness around 47 nm for maximizing current intensity. Future work could explore this optimal range more thoroughly for photodetector applications.
  • Environmental Stability: Although thicker BP offers better inherent stability, long-term operational stability under various environmental conditions would be a crucial area for future research.

Summary updated

BibTeX
@misc{hou2018multilayer,
  author = {Chaojian Hou and Lijun Yang and Bo Li and Qihan Zhang and Yuefeng Li and Qiuyang Yue and Yang Wang and Zhan Yang and Lixin Dong},
  title = {{Multilayer Black Phosphorus Near-Infrared Photodetectors}},
  year = {2018},
  doi = {10.3390/s18061668},
}

Loading related content...

Figure