Moderate-Temperature Pyrolysis Characteristics of Lump Coal Under Varying Coal Particle Sizes

Yuanpei Luo, Lei Liu, Liangguo Lv, Shengping Zhang, Fei Dai, Hongguang Jin, Jun SuiEnergies 2025 · DOI

TL;DR

This study investigates how different lump coal particle sizes (2-30 mm) affect moderate-temperature pyrolysis. The researchers found that an optimal particle size of 10-20 mm balances heat transfer and intra-particle reactions, leading to the highest hydrogen yield and char graphitization. This work provides crucial insights for optimizing industrial lump coal pyrolysis processes.

What Problem Does This Paper Address?

Coal remains a significant global energy source, but its efficient and clean utilization is a major challenge. Pyrolysis offers a promising pathway for converting coal into valuable products like gas, tar, and char, with lump coal pyrolysis having advantages like reduced dust and higher char quality compared to pulverized coal. However, a critical parameter, particle size, significantly influences heat and mass transfer during lump coal pyrolysis, and its governing mechanisms are not well understood. Existing research primarily focuses on pulverized coal (less than 2 mm), leaving a knowledge gap regarding the behavior of larger lump coal particles (2-30 mm) in industrial settings. This paper aims to fill this gap by systematically exploring the impact of particle size on lump coal pyrolysis characteristics.

Methods

The researchers employed a 30 kW pyrolysis experimental apparatus to conduct pyrolysis experiments on low-rank coal from Ordos, Inner Mongolia. They used four distinct particle size ranges: 2–5 mm, 5–10 mm, 10–20 mm, and 20–30 mm. To monitor the process and analyze the products, a comprehensive suite of advanced characterization techniques was utilized:

  • Real-time temperature monitoring: Thermocouples were placed at various heights within the reactor to track the central temperature of the coal bed.
  • Pyrolysis product analysis:
    • Gas Chromatography (GC) and GC-Mass Spectrometry (GC-MS): Used to analyze the composition and yield of pyrolysis gas and tar.
  • Weighing: For determining char yield.
  • Char characterization:
    • Ultimate Analysis: To determine elemental composition.
  • X-ray Diffraction (XRD): To analyze microcrystalline structural parameters (d002, Lc, La) and graphitization degree.
  • Raman Spectroscopy: To investigate the microscopic carbon chemical structure and ordering degree.
  • Brunauer–Emmett–Teller (BET) analysis: To measure specific surface area, total pore volume, and average pore size.
  • Scanning Electron Microscopy (SEM): To visualize the morphology and pore structure of the char.

Datasets

The study utilized low-rank coal from Ordos, Inner Mongolia, as the feedstock. The proximate and ultimate analysis of this coal are presented in Table 1. No new benchmark datasets were introduced; the focus was on experimental characterization of a specific coal type across varying particle sizes.

Key Insights and Ideas

  • Particle size is a critical lever for optimizing lump coal pyrolysis: The study clearly demonstrates that particle size isn't just a minor factor but significantly influences heat transfer, reaction kinetics, and product distribution.
  • The "sweet spot" for lump coal pyrolysis: The 10–20 mm particle size range emerged as optimal. This size range effectively balances rapid heat transfer into the coal bed with manageable intra-particle thermal gradients, leading to more uniform thermal attainment and improved product quality.
  • Competing mechanisms at play: Larger particles improve bed permeability, potentially reducing tar cracking. However, excessively large particles create significant internal temperature differences, hindering core pyrolysis and leading to increased tar cracking.
  • Pore structure evolution is complex: While larger particles generally increase surface area and pore volume, the 10–20 mm group showed an unusual decrease in porosity, attributed to pore collapse from intense polycondensation reactions. This highlights the intricate interplay between particle size and char formation.

Key Results

  • Heat Transfer: Larger particle sizes generally led to faster heat transfer rates in the coal bed due to increased convective heat transfer.
  • Char Yield: Char yield gradually increased with particle size, likely due to slower pyrolysis completion in larger blocks.
  • Gas Yield: The maximum gas yield (6.99 wt.%) was observed for the 20–30 mm particle size group. The highest hydrogen yield (20.99 vol%) was achieved with the 10–20 mm group.
  • Tar Yield: Tar yield initially rose and then declined with increasing particle size, peaking at 14.66 wt.% for the 5–10 mm group. The 10–20 mm group showed the lowest CO yield, consistent with its high tar yield.
  • Char Properties:
    • The 10–20 mm group exhibited the highest C/H ratio, indicating a higher degree of coal graphitization.
  • XRD analysis showed the highest graphitization degree for char from the 10–20 mm particle size.
  • BET analysis revealed an abrupt porosity reduction in the 10–20 mm group.
  • SEM images showed that char from the 10–20 mm group became fragmented and rugged, with pore structures that were not intuitive, possibly due to rapid volatile release.

Limitations and Future Work

  • Resource Availability: The authors acknowledge that lump coal resources are less abundant globally compared to powdered coal, which can be a constraint for widespread industrial adoption.
  • Char Byproduct Accumulation: Significant char byproduct accumulation requires efficient conversion solutions, which is an ongoing challenge for lump coal pyrolysis.
  • Future Research: The authors suggest that future work should focus on optimizing lump coal pyrolysis protocols to enhance the industrial applicability of the derived coke products. Further research into efficient char utilization strategies is also warranted.

Summary updated

Abstract

Pyrolysis is an important methodology for achieving efficient and clean utilization of coal. Lump coal pyrolysis demonstrates distinct advantages over pulverized coal processing, particularly in enhanced gas yield and superior coke quality. As a critical parameter in lump coal pyrolysis, particle size significantly influences heat transfer and mass transfer during pyrolysis, yet its governing mechanisms remain insufficiently explored. This research systematically investigates pyrolysis characteristics of the low-rank coal from Ordos, Inner Mongolia, across graded particle sizes (2–5 mm, 5–10 mm, 10–20 mm, and 20–30 mm) through pyrolysis experiments. Real-time central temperature monitoring of coal bed coupled with advanced characterization techniques—including X-ray diffraction (XRD), Raman spectroscopy, Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), gas chromatography (GC), and GC–mass spectrometry (GC-MS)—reveals particle-size-dependent pyrolysis mechanisms. Key findings demonstrate that the larger particles enhance bed-scale convective heat transfer, accelerating temperature propagation from reactor walls to the coal center. However, excessive sizes cause significant intra-particle thermal gradients, impeding core pyrolysis. The 10–20 mm group emerges as optimal—balancing these effects to achieve uniform thermal attainment, evidenced by 20.99 vol% peak hydrogen yield and maximum char graphitization. Tar yield first demonstrates a tendency to rise and then decline, peaking at 14.66 wt.% for 5–10 mm particles. This behavior reflects competing mechanisms: enlarging particle size can improve bed permeability (reducing tar residence time and secondary reactions), but it can also inhibit volatile release and intensify thermal cracking of tar in oversized coal blocks. The BET analysis result reveals elevated specific surface area and pore volume with increasing particle size, except for the 10–20 mm group, showing abrupt porosity reduction—attributed to pore collapse caused by intense polycondensation reactions. Contrasting previous studies predominantly focused on less than 2 mm pulverized coal, this research selects large-size (from 2 mm to 30 mm) lump coal to clarify the effect of particle size on coal pyrolysis, providing critical guidance for industrial-scale lump coal pyrolysis optimization.
BibTeX
@inproceedings{luo2025moderate,
  author = {Yuanpei Luo and Lei Liu and Liangguo Lv and Shengping Zhang and Fei Dai and Hongguang Jin and Jun Sui},
  title = {{Moderate-Temperature Pyrolysis Characteristics of Lump Coal Under Varying Coal Particle Sizes}},
  booktitle = {Energies},
  year = {2025},
  doi = {10.3390/en18123220},
}
Figure