Modelling and Analysis of Expansion Joints' Effect on Dynamic Performance of Railway Rigid Overhead System

Yang Song, Xiaohe Feng, Zeyao Hu, Shibin Gao, Fuchuan Duan, Wenping Chu, Yang Song 0014Sensors 2023 · DOI

TL;DR

This paper models the dynamic behavior of rigid overhead systems in high-speed railways, focusing on the critical role of expansion joints. By developing detailed finite element models, the researchers found that while expansion joints are generally safe, optimizing their design and installation can significantly reduce stress concentrations and improve the overall performance of the pantograph-overhead system.

What Problem Does This Paper Address?

High-speed rail relies on efficient power collection, which is achieved through the interaction between a pantograph and the overhead system. Rigid overhead contact systems (OCS), common in urban rail, are characterized by high stiffness and low clearance. However, their rigidity can lead to poor current collection quality due to local irregularities. Expansion joints are essential components designed to accommodate thermal expansion and contraction in these systems, preventing damage and ensuring continuity. Despite their importance, the dynamic effects of expansion joints on the overall system performance, particularly under various assembly conditions and thermal loads, require detailed investigation. This paper aims to fill this gap by modeling and analyzing the impact of expansion joints on the dynamic performance of rigid overhead systems.

Methods

The study employs a comprehensive finite element (FE) modeling approach.

  • System Modeling: The rigid overhead system is modeled using beam elements to represent the conductor rail and contact wire, capturing their displacement, stiffness, and mass characteristics.
  • Component Modeling: Key components like suspension structures and positioning line clamps are simplified as equivalent mass-damping-spring elements.
  • Expansion Joint Modeling: A detailed 3D solid FE model of the expansion joint is developed, considering its complex structure and material properties (copper alloy, aluminum alloy, structural steel). Two assembly scenarios are analyzed:
  • Ideal Assembly: Assumes no errors or line pull-out.
  • Deflected Assembly: Accounts for assembly errors and line pull-out, leading to an inclined contact wire.
  • Analysis Techniques:
    • Thermal Analysis: The effect of temperature variations (from -40°C to 40°C) on stress distribution within the expansion joint is simulated.
  • Dynamic Analysis: The influence of the expansion joint's concentrated mass on the pantograph-overhead system's current collection quality is investigated by varying the expansion joint's mass and simulating at different speeds (140, 160, and 180 km/h).
  • Optimization: The paper explores optimization strategies by adjusting the installation deflection angle and modifying the geometric design (chamfer of the slider groove) of the expansion joint to reduce stress concentrations.

Datasets

Not discussed in the paper. The study relies on material properties from standards and experimental data for validation (though specific datasets are not detailed).

Key Insights and Ideas

  • Expansion Joints are Generally Safe, But Not Perfect: While the maximum stresses in the ideal expansion joint model remain within permissible limits, specific areas like the Sliding Block B and Sliding Rod A experience stress concentrations due to the joint's unique assembly.
  • Assembly Matters Significantly: Deflected assembly conditions, caused by installation errors, lead to much higher stresses, particularly in the busbar, Sliding Block B, and Sliding Rod A, pushing some components close to their yield strength. This highlights the critical importance of precise installation.
  • Optimizing Design Reduces Stress: Adjusting the installation deflection angle and increasing the slider groove chamfer in the expansion joint design can significantly reduce stress concentrations and improve safety margins.
  • Mass is a Key Dynamic Factor: The concentrated mass of the expansion joint has a substantial negative impact on the pantograph's current collection quality, especially at higher speeds. Reducing this mass is a direct way to improve system performance.

Key Results

  • Under ideal assembly conditions and varying temperatures, maximum stresses were well below material limits, indicating high safety.
  • In deflected assembly, stresses in the busbar, Sliding Block B, and Sliding Rod A increased significantly, with some exceeding standard-specified stress limits.
  • Reducing the expansion joint's deflection angle from 10° to 5° lowered the maximum stress in Sliding Block B from 280.51 MPa to 193.31 MPa.
  • Increasing the slider groove chamfer from 3.5 mm to 5 mm reduced the stress concentration at Slider B from 281 MPa to 142 MPa.
  • Increasing the expansion joint's mass from 46.4 kg to 69.6 kg led to a noticeable increase in the maximum contact force and standard deviation, indicating poorer current collection quality.

Limitations and Future Work

  • Assembly Imperfections: While the paper models ideal and deflected assembly, real-world scenarios might involve more complex and varied imperfections.
  • Material Properties: The study uses standard material properties; variations in actual manufacturing could influence results.
  • Simplified Pantograph Model: The pantograph is simplified in the dynamic analysis; a more detailed multibody model could provide further insights.
  • Future Work: The authors suggest further optimization of installation deflection angles and geometric designs. They also emphasize the need to reduce the expansion joint's mass to mitigate its negative impact on current collection quality. Further research could explore the long-term effects of these stresses and the interaction with other system components.

Summary updated

BibTeX
@article{song2023modelling,
  author = {Yang Song and Xiaohe Feng and Zeyao Hu and Shibin Gao and Fuchuan Duan and Wenping Chu and Yang Song},
  title = {{Modelling and Analysis of Expansion Joints' Effect on Dynamic Performance of Railway Rigid Overhead System}},
  journal = {Sensors},
  year = {2023},
  doi = {10.3390/s23156797},
}
Figure