Abstract
The dispersion and multiple modes characteristics which exist in the propagation of Lamb waves (LW) in metal plates make it extremely hard to analyze and recognize the detection echo signals of defects. As a newly developed time-frequency analysis method in recent years, Hilbert-Huang transform (HHT) is one of the powerful tools to analyze non-stationary signals. The experimental LW detecting system for single aluminum plate is setup in this work, and the LW detecting signals are analyzed by HHT. The overlapped LW detecting signals of different modes are recognized by the means of extracting flight time of intrinsic mode functions (IMFs) after Hilbert transform (HT). The experiment results, agreeing well with the theoretical analysis, indicate that the HHT method can clearly recognize overlapped LW detecting signals of different modes in metal plates, but could hardly recognize that of the same mode. HHT can be an effective method to recognize LW detecting signals of different modes in metal plates.
Introduction: The Challenge of Lamb Wave Testing
In the field of non-destructive testing (NDT), Lamb waves are a preferred tool for inspecting thin metal plates due to their long-range propagation capabilities. However, their practical application is complicated by two inherent physical phenomena: dispersion and multi-mode characteristics.
Dispersion causes the velocity of the wave to change depending on the excitation frequency. Simultaneously, at any given frequency, multiple modes—such as symmetric (S0) and antisymmetric (A0) waves—can propagate at different speeds. When these waves interact with boundaries or defects, they often overlap in the time domain, creating complex, non-stationary signals where individual wave packets are indistinguishable. Standard analysis tools like Fourier or Wavelet transforms often struggle with these signals because they rely on fixed basis functions that may not match the adaptive nature of the data.
Methodology: Adaptive Signal Processing with HHT
To overcome these limitations, this study utilizes the Hilbert-Huang Transform (HHT), a two-step adaptive signal processing method:
- Empirical Mode Decomposition (EMD): This step decomposes the complex, overlapping signal into several Intrinsic Mode Functions (IMFs). Unlike traditional methods, EMD is data-driven; it derives its "basis" directly from the signal, effectively separating different vibration modes based on their local characteristic time scales.
- Hilbert Transform (HT): Once the IMFs are extracted, the Hilbert Transform is applied to calculate instantaneous amplitude and frequency. This allows for the precise extraction of the "flight time" for individual wave packets.
Experimental Setup
The researchers validated the HHT method using an experimental system consisting of a 3mm thick aluminum plate (100 cm × 100 cm) and Electromagnetic Acoustic Transducers (EMATs). They employed a tone-burst pulse excitation at 83 kHz to generate both S0 and A0 modes.
As illustrated in Figure 3, the setup allowed the team to track various propagation paths, including direct waves and boundary reflections, which naturally result in overlapping signals at the receiver.
Key Results and Discussion
The raw signal collected by the system (Figure 5) demonstrates the difficulty of manual interpretation. While some wave packets are distinct, packet 'c' appears as a single, messy "blob" due to the overlap of different modes.
By applying the HHT method, the researchers successfully untangled these overlapping signals. They were able to separate the direct A0 wave (path #1) from a boundary-reflected S0 wave (path #3) with high precision:
- A0 Mode: Experimental propagation time was 359 μs (Theoretical: 363 μs), representing a 1.1% error.
- S0 Mode: Experimental propagation time was 412 μs (Theoretical: 409 μs), representing a 0.7% error.
A critical insight from the study is that while HHT is excellent at separating different modes (e.g., S0 vs. A0), it struggles to distinguish overlapping signals of the same mode. Because EMD relies on differences in local oscillation characteristics, two overlapping S0 waves are often too similar to be decomposed into separate IMFs.
Conclusion
The Hilbert-Huang Transform provides a powerful, adaptive framework for recognizing multi-mode Lamb wave signals in metal plates. By accurately identifying overlapping wave packets that are invisible in raw time-domain data, HHT offers a clearer path for industrial defect detection. Future research will focus on addressing the challenges of same-mode overlap and applying these techniques to more complex structural geometries.
Summary updated