Miniaturized Polarization Insensitive Metamaterial Absorber Applied on EMI Suppression

Panpan Zuo, Tianwu Li, Mengjun Wang, Hongxing Zheng, Er-Ping LiIEEE Access 2019 · DOI · OpenReview

Abstract

This paper presents the design and analysis of a miniaturized, ultra-thin metamaterial absorber (MMA) specifically engineered for electromagnetic interference (EMI) suppression in the microwave frequency range. The proposed structure utilizes a periodic array of double split-ring resonators printed on an FR4 substrate. Simulations and experimental measurements demonstrate an absorption ratio exceeding 90% across a wide band from 8.3 GHz to 11.3 GHz. The design is notably polarization-insensitive, maintaining high performance for both TE and TM incident waves. Practical application tests show a significant reduction in radiated electric fields, with a maximum suppression of 18 dBμV/m achieved at 10 GHz, making it an ideal candidate for PCB-level EMI mitigation.

Introduction

As electronic devices evolve toward higher data rates and faster signal edge speeds, the resulting harmonic content increasingly falls within the microwave frequency spectrum. This shift generates significant electromagnetic interference (EMI), which can compromise signal integrity and device reliability. Traditional mitigation strategies often involve metallic shielding; however, these shields primarily reflect energy rather than absorbing it, potentially leading to "electromagnetic pollution" within device enclosures.

Metamaterial absorbers (MMAs) offer a superior alternative by converting incident electromagnetic energy into heat. Despite their advantages, many existing MMAs are bulky or sensitive to the polarization of incoming waves. This research addresses these limitations by developing a miniaturized, polarization-insensitive MMA that is both easy to fabricate and highly efficient.

Absorber Design and Methodology

The core of the proposed MMA is a Double Split-Ring Absorber (DSRA) unit cell. The structure consists of two concentric metallic split rings printed on a standard, low-cost FR4 substrate, backed by a continuous metallic ground plane.

Top and perspective views of the proposed double split-ring absorber unit cell.

To achieve polarization independence, the two rings are oriented with their gaps rotated 90° relative to each other. This geometric symmetry ensures that the absorber interacts identically with Transverse Electric (TE) and Transverse Magnetic (TM) wave polarizations. The total thickness of the structure is approximately $0.07 \lambda_0$ at the operating frequency, representing a significant miniaturization over conventional designs. The design process utilized full-wave simulations in CST Studio Suite alongside an Equivalent Circuit Model (ECM) to optimize the RLC parameters for maximum absorption.

Results and Discussion

The MMA achieves an absorption ratio of over 90% from 8.3 GHz to 11.3 GHz, with peak absorption exceeding 95% at 9 GHz and 10.3 GHz. This performance is driven by impedance matching, where the structure's input impedance is tuned to match the $377 \Omega$ impedance of free space, minimizing reflection.

Parametric studies reveal that the resonant frequencies are highly sensitive to the physical dimensions of the rings. As shown in the reflection coefficient (S11) plots, increasing the gap width $p$ or the inner ring radius $R$ allows for precise tuning of the absorption peaks. Specifically, increasing the external ring dimensions tends to lower the first resonant peak, while adjustments to the inner ring shift the second peak.

Simulated reflection coefficient (S11) demonstrating the effect of varying (a) gap width p and (b) inner ring radius R on the absorption peaks.

To validate the design in a real-world scenario, the MMA was loaded onto a 10 GHz patch antenna. Measurements taken in an anechoic chamber showed that the radiated electric field at a distance of 1 meter was reduced by up to 18 dBμV/m. This significant reduction confirms the absorber's effectiveness in suppressing near-field radiation and improving electromagnetic compatibility (EMC).

Conclusion

The developed double split-ring metamaterial absorber provides a robust, miniaturized solution for EMI suppression. Its wideband performance, polarization insensitivity, and thin profile make it highly suitable for integration into high-density electronic packaging. By effectively absorbing rather than reflecting interference, this design offers a practical path toward reducing electromagnetic noise in modern high-speed electronic systems.

Summary updated

Abstract

This paper presents the analysis and design of a miniaturized polarization insensitive metamaterial absorber (MMA) for suppression of the electromagnetic interference (EMI) at microwave frequency range. The proposed MMA consists of a periodic array of double split ring structures printed on an FR4 substrate with a thickness of 0.07 λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0</sub> . The simulated results derived from CST indicate that the absorption ratio of the MMA is over 90% with a wide frequency range from 8.3 GHz to 11.3 GHz for a normal incident electromagnetic (EM) wave. To understand the EM wave absorption mechanism, an equivalent circuit model of the MMA unit cell is constructed to investigate the absorbing characteristics, and the electric field and surface current distributions are analyzed at absorption peaks.. Both equivalent circuit model (ECM) and measured results show good agreement. What's more, the measurement data shows that the radiated electric field of the patch antenna at 1 meter is significantly reduced at 10 GHz while loading with the MMA. A maximum suppression of 18 dBμν/m is achieved at 10 GHz. As the proposed absorber possesses good ability on electromagnetic radiation absorption, it could be well applied on printed circuit board (PCB) level EMI suppression.
BibTeX
@inproceedings{zuo2019miniaturized,
  author = {Panpan Zuo and Tianwu Li and Mengjun Wang and Hongxing Zheng and Er-Ping Li},
  title = {{Miniaturized Polarization Insensitive Metamaterial Absorber Applied on EMI Suppression}},
  booktitle = {IEEE Access},
  year = {2019},
  doi = {10.1109/access.2019.2957308},
}
Figure