Manufacture of Three-Dimensional Optofluidic Spot-Size Converters in Fused Silica Using Hybrid Laser Microfabrication

Jianping Yu, Jian Xu, Aodong Zhang, Yunpeng Song, Jia Qi, Qiaonan Dong, Jianfang Chen, Zhaoxiang Liu, Wei Chen, Ya Cheng2022 · DOI

TL;DR

This paper presents a novel hybrid laser microfabrication technique to create 3D optofluidic spot-size converters (SSCs) in fused silica. By combining femtosecond laser etching with CO2 laser polishing, they demonstrate efficient expansion of optical modes, paving the way for improved fiber-to-chip coupling and advanced photonic devices.

What Problem Does This Paper Address?

Efficiently coupling light from optical fibers into on-chip photonic circuits is a critical challenge in integrated optics. The mismatch in mode field diameter between standard optical fibers (around 9 µm) and typical on-chip waveguides (often much smaller) leads to significant signal loss. While various on-chip solutions like tapered waveguides and grating couplers exist, they often suffer from limitations such as planar configurations, complex fabrication, or restricted flexibility in modulating optical modes. Specifically, achieving simultaneous control over transverse and longitudinal mode fields in 3D is difficult with conventional methods. This paper aims to address this by developing a new, flexible 3D fabrication approach for optofluidic SSCs that can effectively bridge this mode mismatch.

Methods

The authors propose a two-step hybrid laser microfabrication process:

  1. Femtosecond (fs) Laser-Assisted Chemical Etching: Spatially shaped fs laser pulses are used to create 3D hollow microchannels in fused silica. This process involves direct laser writing to modify the glass structure, followed by selective chemical etching (using KOH solution) to remove the modified regions, forming the microchannels. The key innovation here is the use of a slit-beam shaping technique to achieve spatially symmetric modification and create complex 3D channel geometries, including tapered sections.
  2. CO2 Laser-Induced Thermal Reflow: After the initial microchannel fabrication, a defocused CO2 laser is used to irradiate the internal surfaces of the channels. This thermal process smooths the etched surfaces, improving optical performance, and also helps to seal off unwanted smaller access ports.

Finally, the fabricated 3D microchannels are filled with a liquid-core waveguide solution (a mixture of n-decane and liquid paraffin) to create the optofluidic SSC structures.

Datasets

Not discussed in the paper. The experiments involve fabricating and characterizing custom devices rather than training on existing datasets.

Key Insights and Ideas

  • Hybrid Approach Synergy: The combination of fs laser etching for precise 3D structuring and CO2 laser reflow for surface smoothing is crucial. The fs laser creates the complex geometry, while the CO2 laser enhances its optical quality and functionality.
  • Optofluidic Flexibility: Using a liquid core offers inherent tunability. By changing the liquid, the optical properties of the waveguide can be modified, opening doors for dynamic photonic devices.
  • 3D Tapering for Mode Expansion: The ability to create precisely tapered 3D channels is key to achieving adiabatic mode conversion, which is essential for efficient spot-size expansion.
  • Sealing with CO2 Laser: The CO2 laser's ability to seal off smaller access ports simplifies the final device structure and prevents leakage of the liquid core.
  • Quasi-Microlens Effect: The hemispherical shape of the coupling terminals, a byproduct of the etching process, acts as a microlens, further improving coupling efficiency by reducing the divergence angle of the outgoing light.

Key Results

  • Mode Expansion: The fabricated optofluidic SSC structure successfully expanded the fundamental mode field diameter from approximately 8 µm to 23 µm.
  • Conversion Efficiency: The measured mode-field conversion efficiency was approximately 84.1%.
  • Reduced Insertion Loss: For waveguide-to-waveguide coupling devices, the use of two symmetric SSC structures with ~50 µm diameter coupling ports resulted in a total insertion loss of ~6.73 dB. This is significantly lower (about half) than non-SSC structures with ~9 µm diameter coupling ports over the same distance.
  • Improved Coupling Distance: The SSC structures provide a larger mode size and a longer Rayleigh distance (~317 µm for SSC vs. ~48 µm for non-SSC), enabling more efficient coupling over longer distances.

Limitations and Future Work

  • Residual Roughness: The authors acknowledge that the conversion efficiency (84.1%) was lower than the simulated value (~95%) and attribute this to potential losses caused by residual roughness on the inner walls of the tapered channel after CO2 laser treatment.
  • Port Size Optimization: Further optimization of the heat-affected zone and the spatial sizes of the extra-access ports is suggested to improve sealing and control.
  • Tunability Exploration: While the optofluidic nature offers tunability, this paper focuses on a specific liquid core. Future work could explore a wider range of liquids and their impact on device performance.
  • Broader Applications: The authors suggest that this technique holds great potential for various applications, including on-chip detection with high sensitivity, lab-on-a-chip devices, and biochips, implying future research directions in these areas.

Summary updated

BibTeX
@misc{yu2022manufacture,
  author = {Jianping Yu and Jian Xu and Aodong Zhang and Yunpeng Song and Jia Qi and Qiaonan Dong and Jianfang Chen and Zhaoxiang Liu and Wei Chen and Ya Cheng},
  title = {{Manufacture of Three-Dimensional Optofluidic Spot-Size Converters in Fused Silica Using Hybrid Laser Microfabrication}},
  year = {2022},
  doi = {10.3390/s22239449},
}

Loading related content...

Figure