Abstract
Fluid leakoff remains a critical challenge in hydraulic fracturing, particularly in water-sensitive shale reservoirs. This study evaluates the performance of $CO_2$ foams stabilized with nanosilica particles. By measuring gas and liquid leakoff phases independently under high-pressure conditions (1,300 psi), the research demonstrates that nanoparticle-enhanced foams can reduce liquid loss by orders of magnitude compared to traditional water-based fluids. The findings highlight the role of the Jamin effect and temporary filter cake formation in enhancing fracture pressure maintenance.
Introduction
In hydraulic fracturing, maintaining high fluid pressure is essential for propagating cracks in rock formations. However, "leakoff"—the migration of fracturing fluid into the surrounding porous rock—often undermines this process. High leakoff rates can lead to "screen outs," where proppants bridge the fracture prematurely. While water-based fluids are standard, they often cause clay swelling in shale, damaging reservoir permeability. $CO_2$ foams offer a low-water alternative, but their complex leakoff behavior, involving distinct gas and liquid phase migration, has historically been under-studied. This research addresses this gap by assessing nanoparticle-stabilized foams under both dynamic and static conditions.
Experimental Methodology
The researchers developed a specialized high-pressure experimental apparatus to simulate deep-well environments. The system, illustrated in Figure 1, allows for the generation of $CO_2$ foam using a beadpack mixer and the subsequent measurement of leakoff through rock core samples.
The foam was stabilized using 7nm nanosilica particles, with additional tests incorporating Sodium Dodecyl Sulfate (SDS) as a surfactant and Hydroxyethyl Cellulose (HEC) as a polymer. A key innovation in this setup is the separate tracking of gas and liquid phases using a gas flowmeter and a digital scale, providing a more granular view of leakoff dynamics than conventional total-fluid measurements.
Rock Samples and Test Parameters
The study utilized three distinct sandstone core samples to evaluate the impact of rock texture and permeability on fluid loss. The properties of these samples are summarized in the table below.
A total of 15 experimental runs were conducted, varying $CO_2$ foam quality (0% to 90%), chemical concentrations, and rock permeability. Pure water served as the control baseline for all comparisons.
Results and Discussion
The Jamin Effect and Foam Stability
The experiments confirmed that as foam flows across the rock face, bubbles become trapped in pore throats—a phenomenon known as the Jamin effect. This creates a bottleneck that significantly impedes liquid loss. Nanosilica particles enhance this effect by stabilizing a finer foam texture. Furthermore, the nanoparticles form a temporary "filter cake" on the rock surface. This cake effectively blocks leakoff during pumping but is easily removed during flowback, minimizing permanent formation damage.
Optimal Foam Quality
The researchers identified 70% $CO_2$ as the optimal foam quality for minimizing dynamic liquid leakoff. At this ratio, the liquid leakoff coefficient was reduced from 0.2643 $ft/\sqrt{min}$ (pure water) to as low as 0.00051 $ft/\sqrt{min}$. Increasing the quality to 90% resulted in an unstable "dry" foam, which actually increased leakoff rates.
Influence of Permeability and Additives
Rock permeability proved to be the primary driver of fluid loss; a 12-fold increase in permeability resulted in a 140-fold increase in dynamic liquid leakoff. The addition of SDS surfactant showed a strong synergy with nanoparticles, completely halting gas leakoff in low-permeability rocks by refining the foam structure. While HEC polymer further reduced leakoff, its impact was secondary to that of foam quality and nanoparticle stabilization.
Conclusion
Nanoparticle-stabilized $CO_2$ foams represent a highly effective solution for fracturing water-sensitive reservoirs. By significantly reducing both liquid and gas leakoff through the Jamin effect and temporary filter cake formation, these fluids allow for better pressure maintenance and reduced formation damage. Future work should focus on the performance of these foams at higher temperatures and their interactions with a broader range of chemical additives.
Summary updated