Large Range Curvature Measurement Using FBGs in Two-Core Fiber with Protective Coating

Ruibin Chen, Lutian Li, Qianqing Yu, Zhijun Luo, Zhenggang Lian, Chuanxin Teng, Hang Qu, Xuehao HuMicromachines 2024 · DOI

TL;DR

This paper introduces a novel fiber optic sensor using two Fiber Bragg Gratings (FBGs) inscribed in a specialty two-core fiber. This sensor offers a large measurement range and robust performance for curvature detection, with built-in compensation for temperature and humidity variations, making it suitable for demanding engineering applications.

What Problem Does This Paper Address?

Accurate and reliable measurement of bending or curvature is crucial in many fields, including aerospace, robotics, and structural health monitoring. Traditional methods often face limitations in terms of size, complexity, or sensitivity. Fiber optic sensors, particularly those based on Fiber Bragg Gratings (FBGs), offer a promising alternative due to their small size, immunity to electromagnetic interference, and multiplexing capabilities. However, achieving a large measurement range while maintaining high sensitivity and compensating for environmental factors like temperature and humidity has been a persistent challenge. Existing FBG-based bending sensors often require specially designed, axially asymmetrical fibers, and their sensing range can be limited, especially when dealing with fragile fiber structures. This work aims to address these limitations by developing a robust, high-performance curvature sensor with an extended range and inherent environmental compensation.

Methods

The core innovation lies in the use of a specialty two-core optical fiber with a unique cross-section: a central core, an eccentric core, and an adjacent air channel. Two FBGs were inscribed directly into these cores using a femtosecond laser and a point-by-point (PbP) direct writing technique. This method allows for precise control over grating parameters and inscription location.

  • Fiber Preparation: A specialty two-core fiber with an outer diameter of ~250 µm (including coating) and a bare fiber diameter of 125 µm was used. It features a central core (~8.1 µm), an eccentric core (~9.2 µm), and an air channel (~36 µm).
  • FBG Inscription: A femtosecond laser system (520 nm wavelength, 346 fs pulse duration) was employed for PbP inscription. This technique allows for the creation of FBGs with different periods in each core, enabling distinct spectral responses.
  • Sensor Fabrication: The specialty fiber was spliced to a standard single-mode fiber (SMF) pigtail and a short section of multimode fiber (MMF) acting as a beam expander to efficiently couple light into both cores.
  • Curvature Measurement Setup: A custom experimental setup was designed to bend the fiber between two moving stages. The curvature was calculated based on the displacement of the stages and the initial fiber length. Experiments were conducted in four orthogonal orientations (0°, 90°, 180°, 270°) to capture directional bending responses.
  • Environmental Compensation: The temperature and humidity cross-sensitivity were investigated by exposing the sensor to controlled temperature variations and immersing it in water. The difference in spectral shifts between the two FBGs was analyzed to demonstrate compensation.

Datasets

Not discussed in the paper. The experiments involved controlled bending, temperature, and humidity variations, with data collected from the sensor's spectral response.

Key Insights and Ideas

  • Asymmetric Fiber Design is Key: The distinct placement of the two cores (central and eccentric) and the presence of an air channel create an inherent asymmetry in the fiber. This asymmetry leads to different bending responses in each core, which is crucial for both directional sensing and environmental compensation.
  • Differential Spectral Shifts for Compensation: The most significant insight is the ability to compensate for temperature and humidity effects by analyzing the difference in wavelength shifts between the two FBGs. While each FBG shifts individually due to environmental factors, their relative shifts remain consistent, allowing for the isolation of the curvature-induced shift.
  • Protective Coating Enhances Range: The inclusion of a protective buffer coating significantly increases the sensor's robustness, allowing for a much larger curvature measurement range (up to 50 m⁻¹ and potentially beyond) without fiber breakage, outperforming previous studies.
  • Directional Sensitivity: The sensor exhibits distinct sensitivities depending on the bending direction relative to the fiber's core arrangement, enabling directional curvature measurements.

Key Results

  • High Bending Sensitivity: The FBG in the eccentric core achieved a maximum bending sensitivity of 58 pm/m⁻¹ over a curvature range of 0–50 m⁻¹.
  • Large Sensing Range: The protective coating enabled a robust sensing range of 0–50 m⁻¹, with potential to extend beyond 200 m⁻¹ without fiber breakage.
  • Temperature Sensitivity: The central core FBG showed a sensitivity of 14.6 pm/°C, and the eccentric core FBG showed 16.0 pm/°C. The difference in spectral shifts due to temperature was minimal (max variation of 0.035 nm over 25°C).
  • Humidity Sensitivity: Both FBGs showed a redshift of approximately 0.06 nm when exposed to a saturated humidity environment. The difference in spectral shifts due to humidity was also small (max difference of 0.02 nm).
  • Directional Dependence: Sensitivities varied significantly with orientation, with the eccentric core FBG showing strong responses at 0° and 180° orientations and weak responses at 90° and 270°.

Limitations and Future Work

  • Nonlinearity at High Curvatures: While the sensor demonstrates linearity up to 50 m⁻¹, nonlinearity becomes observable for curvatures greater than 60 m⁻¹. The paper notes that a 3-point fitting technique was used to estimate curvature beyond this range, indicating a need for advanced signal processing for very high curvatures.
  • Coating Degradation: The authors acknowledge that the polyacrylate coating may degrade over long-term outdoor use due to factors like hydrolysis and photodegradation.
  • Future Work: The authors suggest further optimizing the sensor design, improving its long-term stability and reliability, and exploring its performance in practical applications. They also mention the potential for multi-parameter applications beyond just bending due to the integrated fluidic channel.

Summary updated

Abstract

In this work, we propose a fiber Bragg grating (FBG)-based sensor for curvature measurements. Two gratings are inscribed through the protective coating in a specialty optical fiber using focused femtosecond laser pulses and point-by-point direct writing technology. One grating is inscribed on the central core adjacent to an air channel, while the other is inscribed on the eccentric core. The bending characteristics of the two-core fiber strongly depend on the bending direction due to the asymmetry of the fiber cores. A bending sensitivity of 58 pm/m-1 is achieved by the FBG in the eccentric fiber core over the curvature range of 0-50 m-1. Temperature and humidity cross-sensitivity could be significantly reduced by analyzing the differences in peak shifts between the two gratings. The sensor features a large sensing range and good robustness due to the presence of its protective buffer coating, which makes it a good candidate for curvature sensing in engineering fields.
BibTeX
@inproceedings{chen2024large,
  author = {Ruibin Chen and Lutian Li and Qianqing Yu and Zhijun Luo and Zhenggang Lian and Chuanxin Teng and Hang Qu and Xuehao Hu},
  title = {{Large Range Curvature Measurement Using FBGs in Two-Core Fiber with Protective Coating}},
  booktitle = {Micromachines},
  year = {2024},
  doi = {10.3390/mi15111310},
}
Figure