Large-area and bright pulsed electroluminescence in monolayer semiconductors

Der‐Hsien Lien, Matin Amani, Sujay B. Desai, Geun Ho Ahn, Kevin Han, Jr‐Hau He, Joel W. Ager, Ming C. Wu, Ali JaveyNature Communications 2018 · DOI

TL;DR

Researchers have developed a novel transient-mode electroluminescent device using monolayer transition-metal dichalcogenides (TMDCs) that overcomes the limitations of previous TMDC light-emitting devices. This new approach enables bright, large-area, and transparent displays, paving the way for next-generation optoelectronic applications.

What Problem Does This Paper Address?

Monolayer transition-metal dichalcogenides (TMDCs) like MoS₂, WS₂, MoSe₂, and WSe₂ are promising materials for optoelectronics due to their excellent optical properties, such as near-unity photoluminescence quantum yield. However, creating efficient light-emitting devices from these materials has been a significant challenge. Traditional light-emitting diodes (LEDs) require ohmic contacts for efficient electron and hole injection, which are difficult to achieve with TMDCs. Previous attempts to create TMDC-based LEDs have relied on complex heterostructures or doping techniques, limiting their scalability and performance. This paper addresses the need for a simpler, more efficient, and scalable method to achieve electroluminescence (EL) in TMDCs.

Methods

The core innovation in this paper is the development of a "transient-mode electroluminescent" (t-EL) device. Instead of relying on steady-state operation and ohmic contacts, this device utilizes a two-terminal configuration with a single metal-semiconductor contact (the source). An AC voltage is applied between the gate and the source. During the rapid voltage transients, a large, temporary injection of both electrons and holes occurs into the TMDC layer from the source contact. This transient injection mechanism effectively bypasses the need for perfect ohmic contacts and allows for bright EL even with Schottky contacts. The researchers also employed time-resolved EL (TREL) measurements to understand the dynamic operation and carrier injection mechanisms. Device simulations using Sentaurus TCAD were performed to model the band diagrams, carrier densities, and recombination rates.

Datasets

Not discussed in the paper. The study focuses on experimental device fabrication and characterization using various TMDC materials.

Key Insights and Ideas

  • Transient Injection is Key: The most significant insight is that rapid voltage changes (transients) can induce substantial carrier injection into TMDCs, even through Schottky barriers. This "transient-mode" operation is the fundamental breakthrough.
  • Schottky Barrier Independence: The EL intensity is remarkably insensitive to the Schottky barrier height or the polarity of the contact. This is a major advantage over traditional devices where contact quality is paramount.
  • Scalability and Transparency: The t-EL device concept is shown to be scalable to millimeter dimensions and can be fabricated to be transparent, opening up new display applications.
  • Material Versatility: The approach works across multiple TMDC materials (MoS₂, WS₂, MoSe₂, and WSe₂), demonstrating its broad applicability.
  • PL QY Droop is a Limiting Factor: The paper identifies the photoluminescence quantum yield (PL QY) droop at high injection levels, attributed to biexcitonic recombination, as a primary limitation for achieving higher efficiencies.

Key Results

  • Bright EL: The t-EL devices achieve bright EL, with a peak power of 193 µW cm⁻² demonstrated from a ~0.7 nm thick monolayer in ambient room lighting.
  • Millimeter-Scale Display: The researchers successfully fabricated a seven-segment display using monolayer WSe₂ that can dynamically show letters (C-A-L).
  • Transparent Devices: Large-area, transparent t-EL devices were demonstrated on quartz substrates using ITO electrodes.
  • Efficiency Improvements: While initial EL external efficiencies were around 0.06%, treatment of WS₂ with a superacid improved this to ~0.27%, with an internal efficiency (ηᵢ) of ~1.2%. The paper suggests potential for ηᵢ to reach ~40% with further engineering.
  • Weak Dependence on Contact Material: EL intensity showed only a ~4x variation across different metal contacts (Au, Ag, Ni, MoOx, Graphene), highlighting the robustness of the transient injection mechanism.

Limitations and Future Work

  • Efficiency Limitations: The authors acknowledge that the internal efficiency (ηᵢ) is still limited by the PL QY droop at high injection levels, which is caused by biexcitonic recombination.
  • Future Work:
    • Improving Efficiency: Further improvements in efficiency can be achieved by engineering the optical medium to influence radiative lifetime and biexcitonic recombination rates.
  • Exploring Larger Bandgap Materials: The transient injection concept is expected to be applicable to other materials, particularly those with larger bandgaps where ohmic contacts are even more challenging.
  • Advanced Integration: The exposed light-emitting surface of these devices allows for direct integration with plasmonic structures, nano-antennas, and photonic crystals for high-speed devices or electrically pumped 2D lasers.

Summary updated

Abstract

Transition-metal dichalcogenide monolayers have naturally terminated surfaces and can exhibit a near-unity photoluminescence quantum yield in the presence of suitable defect passivation. To date, steady-state monolayer light-emitting devices suffer from Schottky contacts or require complex heterostructures. We demonstrate a transient-mode electroluminescent device based on transition-metal dichalcogenide monolayers (MoS<sub>2</sub>, WS<sub>2</sub>, MoSe<sub>2</sub>, and WSe<sub>2</sub>) to overcome these problems. Electroluminescence from this dopant-free two-terminal device is obtained by applying an AC voltage between the gate and the semiconductor. Notably, the electroluminescence intensity is weakly dependent on the Schottky barrier height or polarity of the contact. We fabricate a monolayer seven-segment display and achieve the first transparent and bright millimeter-scale light-emitting monolayer semiconductor device.
BibTeX
@inproceedings{lien2018large,
  author = {Der‐Hsien Lien and Matin Amani and Sujay B. Desai and Geun Ho Ahn and Kevin Han and Jr‐Hau He and Joel W. Ager and Ming C. Wu and Ali Javey},
  title = {{Large-area and bright pulsed electroluminescence in monolayer semiconductors}},
  booktitle = {Nature Communications},
  year = {2018},
  doi = {10.1038/s41467-018-03218-8},
}
Figure