Joint Beamforming and Matching for Ultra-Dense Massive Antenna Arrays

Carolina Nolasco-Ferencikova, Georg Schwan, Raphael Rolny, Alexander Stutz-Tirri, Christoph StuderarXiv 2025 · DOI · arXiv

Introduction

Massive MIMO (Multiple-Input Multiple-Output) is a cornerstone of modern wireless communication, significantly boosting spectral efficiency. However, scaling these systems to ultra-large antenna arrays presents a formidable hardware challenge. Traditional "all-digital" architectures require a dedicated RF chain for every antenna, leading to prohibitive costs and power consumption. Hybrid architectures attempt to mitigate this by using fewer RF chains and networks of phase shifters, but these phase shifters remain expensive components.

This paper proposes a highly efficient, switch-based hybrid beamforming architecture that jointly optimizes beamforming and impedance matching. By utilizing a rigorous, physically consistent electromagnetic model, the authors demonstrate that a low-cost design can achieve performance comparable to all-digital systems while using 16 times fewer RF chains.

System Architecture and Joint Design

To address the hardware bottleneck, the researchers introduced a cost-efficient hybrid beamformer based on three key pillars:

  1. Tiling: The antenna array is partitioned into 4×4 tiles. Each tile of 16 antennas is driven by a single Power Amplifier (PA) and RF chain.
  2. Joint Matching & Beamforming: Instead of separate stages, the PA connects to a reconfigurable matching network—a triple-stub tuner utilizing RF switches—followed by a power splitter and individual switch units at each antenna.
  3. Simplified Phase Shifting: Standard high-resolution phase shifters are replaced by simple units containing two RF switches. These provide four discrete states: pass-through, 180° phase shift, open-circuit reflection, and short-circuit reflection.
System model of the proposed hybrid beamforming architecture showing the RF frontend, tuning network, and radiating structure.

This co-design approach allows the system to dynamically compensate for the severe impedance variations caused by mutual coupling in ultra-dense arrays (inter-element spacing of $\lambda/4$).

The Importance of Physical Consistency

A critical contribution of this work is the use of the Reconfigurable Electromagnetic Structures (REMS) modeling framework. Previous studies often relied on simplified models that ignored real-world physics like mutual antenna coupling, ohmic losses, and impedance mismatch. The REMS framework captures circuit-theoretic power waves, scattering parameters, and far-field radiation patterns, providing a realistic evaluation of the switch-based design.

The study applied this framework to ultra-dense 4×4 and 16×16 patch antenna arrays operating at 12 GHz. The results underscore that physically consistent modeling is essential for accurately predicting the behavior of highly constrained, low-cost RF hardware.

Performance and Efficiency

The proposed architecture was benchmarked against all-digital systems with both ideal and conventional impedance matching. The primary metric, "REMS gain," accounts for directivity, losses, and mismatch.

Comparison of normalized beamforming gain (REMS gain relative to directivity) for the proposed architecture versus all-digital benchmarks across 4x4 and 16x16 arrays.

Key results include:

  • Near All-Digital Performance: The switch-based architecture achieves a beamforming gain only ~1 dB lower than a practical all-digital architecture with conventional matching, despite the 16-fold reduction in RF chains.
  • Proximity to Theoretical Limits: The system stays within 4.4 dB (for 4×4) and 5.8 dB (for 16×16) of a theoretical all-digital system with perfect, ideal matching.
  • Superior Hardware Efficiency: Using a Cost-Aware Metric (CAM) to measure gain per RF chain, the proposed design delivers approximately 11 dB higher gain per RF chain compared to conventional all-digital setups.

Conclusion and Future Outlook

While the proposed switch-based architecture shows immense promise for reducing the cost of massive antenna arrays, challenges remain. The optimization of switch states involves a massive search space, requiring heuristic algorithms like coordinate ascent for larger arrays. Furthermore, while this study focused on ultra-dense $\lambda/4$ spacing, future work will explore the trade-offs between this density and standard $\lambda/2$ arrays. Nonetheless, the results prove that clever joint design and simple RF switches can effectively replace expensive components in future Massive MIMO systems.

Summary updated

BibTeX
@misc{nolascoferencikova2025joint,
  author = {Carolina Nolasco-Ferencikova and Georg Schwan and Raphael Rolny and Alexander Stutz-Tirri and Christoph Studer},
  title = {{Joint Beamforming and Matching for Ultra-Dense Massive Antenna Arrays}},
  year = {2025},
  eprint = {2512.02628},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2512.02628},
}
Figure