Investigation of Component Interactions During the Hydrothermal Process Using a Mixed-Model Cellulose/Hemicellulose/Lignin/Protein and Real Cotton Stalk

Shengjun Guo, Jiachen Zuo, Xiao Yang, Hui Wang, Lihua Cheng, Libo ZhangEnergies 2025 · DOI

TL;DR

This study investigates how the proportions of cellulose, hemicellulose, lignin, and protein in biomass affect bio-oil production during low-temperature hydrothermal liquefaction (HTL). They found that cellulose and lignin strongly interact to boost bio-oil yield, while cellulose and hemicellulose inhibit each other. Understanding these interactions is crucial for optimizing bio-oil production from agricultural waste like cotton stalks.

What Problem Does This Paper Address?

Converting agricultural and forestry waste into valuable bio-oil through hydrothermal liquefaction (HTL) is a promising avenue for sustainable energy and chemical production. However, current research often focuses on optimizing HTL parameters like temperature and time, with less attention paid to how the composition of the biomass feedstock influences the process and the resulting bio-oil. Lignocellulosic biomass, like cotton stalks, is a complex mixture of cellulose, hemicellulose, and lignin, with varying amounts of protein. The interactions between these components during HTL are not well understood, making it difficult to predict and control bio-oil yield and quality, especially when co-liquefying different biomass sources. This paper aims to fill this knowledge gap by systematically studying the interactions between these core components, both in model systems and real cotton stalk, under mild HTL conditions.

Methods

The researchers employed a mixed-model approach, using purified cellulose, hemicellulose (xylan), lignin (lignosulfonate), and protein (glycine) as model components. They conducted hydrothermal liquefaction experiments at a relatively low temperature (220 °C) for 4 hours. The core of their methodology involved:

  • Monocomponent experiments: Testing each component individually to establish baseline bio-oil yields.
  • Binary blending: Mixing two components at various ratios (e.g., cellulose-lignin, cellulose-hemicellulose, hemicellulose-lignin) to observe their interactions.
  • Multivariate blending: Creating ternary (three components) and quaternary (four components, including protein) mixtures, often mimicking the approximate composition of real cotton stalk.
  • Real cotton stalk HTL: Performing HTL on actual cotton stalk to compare with the model system results.

After HTL, the bio-oil yield was determined gravimetrically. The bio-oil was then characterized using:

  • Fourier Transform Infrared Spectroscopy (FTIR): To identify functional groups.
  • Elemental Analysis (EA): To determine the elemental composition (C, H, N, S, O).
  • Gas Chromatography-Mass Spectrometry (GC-MS): To analyze the detailed composition of organic compounds in the bio-oil.
  • Thermogravimetric Analysis (TGA): To assess thermal stability.

Datasets

The study utilized purified chemical components (cellulose, xylan, lignosulfonate, glycine) as model feedstocks. The primary "dataset" for comparison was the bio-oil produced from real cotton stalk collected from Karamay, Xinjiang, China. No new benchmark datasets were introduced; rather, the study aimed to provide insights into the interactions within a common lignocellulosic biomass.

Key Insights and Ideas

  • Cellulose-Lignin Synergy is Key: The most significant finding is the strong synergistic interaction between cellulose and lignin, leading to a substantial increase in bio-oil yield (up to 6.82% in binary blends). This suggests that lignin plays a crucial role in promoting the conversion of cellulose into valuable liquid products.
  • Cellulose-Hemicellulose Inhibition: Conversely, cellulose and hemicellulose exhibit an inhibitory interaction, reducing bio-oil yield. This effect is more pronounced at higher cellulose content.
  • Protein Boosts Yield (Especially with Cellulose): The addition of glycine (a protein model) generally enhanced bio-oil yields, with the most significant improvement seen in cellulose-glycine blends. This is attributed to Maillard reactions between amino acids and carbohydrates.
  • Composition Dictates Bio-oil Quality: The relative proportions of components in the HTL mixture significantly influence the composition and properties of the resulting bio-oil, including its high heating value (HHV).
  • Lignin's Role in Inhibiting Coke Formation: Lignin appears to inhibit the formation of coke and volatile substances from cellulose, promoting the generation of lighter compounds in the bio-oil.
  • Cotton Stalk Complexity: The interactions observed in the model systems largely mirrored those in real cotton stalk, confirming that cellulose, hemicellulose, and lignin are the primary drivers of bio-oil formation, with protein playing a supporting role.

Key Results

  • Yield Enhancement: Cellulose-lignin (C-L) binary blends showed a synergistic yield increase of 6.82%. Cellulose-hemicellulose (C-X) showed an inhibitory effect of 1.83%, and hemicellulose-lignin (X-L) had a non-significant interaction of 1.32%.
  • Protein Impact: Cellulose-glycine (C-G) blends saw bio-oil yield increase from 2.29% to 4.59%.
  • High Heating Value (HHV): Aqueous-phase bio-oil from hemicellulose-glycine (X-G) blends achieved the highest HHV of 29.364 MJ/kg.
  • Component Ratio Matters: The cellulose-lignin interaction reached maximum efficacy at a 3:1 mass ratio.
  • Bio-oil Composition: GC-MS analysis revealed that cellulose and hemicellulose primarily contribute to non-aryl compounds (ketones, aldehydes, esters), while lignin yields phenolic, polyheterocyclic, and aromatic compounds. Interactions can redirect these pathways.

Limitations and Future Work

  • Mild Conditions: The study was conducted under relatively mild HTL conditions (220 °C). While this is beneficial for energy efficiency, exploring higher temperatures and catalytic approaches could reveal different interaction dynamics.
  • Model Component Purity: While model components were used, real biomass contains a more complex array of minor constituents and structural variations that could influence interactions.
  • Scale-Up Challenges: The authors acknowledge that current research is primarily lab-scale. Scaling up HTL processes faces challenges like heat and mass transfer limitations, which could alter component interactions and product yields.
  • Future Directions:
    • Improving Oil Quality: Focus on enhancing bio-oil stability and reducing impurities (N and S heteroatoms) through efficient catalytic processes.
  • Scale-Up Solutions: Investigating strategies to overcome mass and heat transfer limitations during scale-up.
  • Comprehensive Utilization: Developing technologies for the valorization of all HTL products (aqueous phase, solid residues) beyond just bio-oil.
  • Life Cycle Assessment (LCA): Quantifying the environmental and economic benefits of integrated biomass conversion strategies.

Summary updated

Abstract

Converting agricultural and forestry waste into high-value-added bio-oil via hydrothermal liquefaction (HTL) reduces incineration pollution and alleviates fuel oil shortages. Current research focuses on adjusting HTL parameters like temperature, time, catalyst, and pretreatment. Few studies explore raw material composition and its interactions with bio-oil properties, limiting guidance for future multi-material hydrothermal co-liquefaction. In view of the above problems, the lignocellulosic model in this paper used cellulose, hemicellulose, lignin, and protein as raw materials. At a low hydrothermal temperature (220 °C), the yield and properties of hydrothermal bio-oil were used as indicators to explore the influence of the proportional content of different model components on the interaction in the hydrothermal process through its simple binary blending and multivariate blending. Then, compared with the hydrothermal liquefaction process of cotton stalk, the interaction between components in the hydrothermal process of real lignocellulose was explored. The results demonstrated significant interactions among cellulose, lignin, and hemicellulose in cotton stalks. The relative strength of component interactions was ranked by yield (wt.%) and property modulation as follows: cellulose–lignin (C-L, 6.82%, synergistic enhancement) > cellulose–hemicellulose (C-X, 1.83%, inhibitory effect) > hemicellulose–lignin (X-L, 1.32%, non-significant interaction). Glycine supplementation enhanced bio-oil yields, with the most pronounced effect observed in cellulose–glycine (C-G) systems, where hydrothermal bio-oil yield increased from 2.29% to 4.59%. Aqueous-phase bio-oil exhibited superior high heating values (HHVs), particularly in hemicellulose–glycine (X-G) blends, which achieved the maximum HHV of 29.364 MJ/kg among all groups. Meanwhile, the characterization results of hydrothermal bio-oil under different mixing conditions showed that the proportion of model components largely determined the composition and properties of hydrothermal bio-oil, which can be used as a regulation method for the synthesis of directional chemicals. Cellulose–lignin (C-L) interactions demonstrated the strongest synergistic enhancement, reaching maximum efficacy at a 3:1 mass ratio. This study will deepen the understanding of the composition of lignocellulose raw materials in the hydrothermal process, promote the establishment of a hydrothermal product model of lignocellulose, and improve the yield of bio-oil.
BibTeX
@inproceedings{guo2025investigation,
  author = {Shengjun Guo and Jiachen Zuo and Xiao Yang and Hui Wang and Lihua Cheng and Libo Zhang},
  title = {{Investigation of Component Interactions During the Hydrothermal Process Using a Mixed-Model Cellulose/Hemicellulose/Lignin/Protein and Real Cotton Stalk}},
  booktitle = {Energies},
  year = {2025},
  doi = {10.3390/en18051290},
}
Figure