Insights into SnO2 Nanoparticles Supported on Fibrous Mesoporous Silica for CO Catalytic Oxidation

Guobo Li, Yingying Zhang, Jie Yan, Yiwei Luo, Conghui Wang, Weiwei Feng, Shule Zhang, Wenming Liu, Zehui Zhang, Honggen PengCatalysts 2023 · DOI

TL;DR

This paper presents a novel catalyst, SnO2 nanoparticles supported on fibrous mesoporous silica (KCC-1), that demonstrates excellent low-temperature CO catalytic oxidation. The unique KCC-1 structure ensures highly dispersed SnO2 nanoparticles, leading to superior activity and stability compared to other materials, and the study elucidates the reaction mechanism using advanced spectroscopic and computational techniques.

What Problem Does This Paper Address?

Carbon monoxide (CO) is a significant air pollutant originating from various industrial processes and combustion sources. Its catalytic oxidation is a crucial method for CO elimination, especially for environmental air quality standards. While precious metals like Pt and Au are highly effective catalysts, their high cost and scarcity limit widespread application. This has driven research into non-noble metal catalysts. Tin dioxide (SnO2) has shown promise due to its comparable catalytic activity and stability. However, a major challenge for both precious and non-noble metal catalysts is the tendency for active nanoparticles to agglomerate, leading to reduced surface area and catalytic efficiency over time. This paper addresses the need for highly stable and efficient non-precious metal catalysts for CO oxidation by developing a strategy to prevent nanoparticle aggregation and enhance catalytic performance.

Methods

The researchers employed a multi-pronged approach combining synthesis, advanced characterization, and theoretical calculations:

  • Synthesis: They synthesized a fibrous mesoporous silica material, KCC-1, and then loaded tin dioxide (SnO2) nanoparticles onto its surface. Different loadings of SnO2 were explored (Snx@KCC-1). For comparison, they also prepared SnO2 nanoparticles supported on MCM-41 (a different mesoporous silica) and pristine SnO2 nanoparticles.
  • Characterization:
    • Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM): Used to visualize the morphology and dispersion of SnO2 nanoparticles on the KCC-1 support.
  • X-ray Diffraction (XRD): To analyze the crystalline structure of the catalysts and confirm the presence of SnO2.
  • Nitrogen Adsorption-Desorption (BET and BJH analysis): To determine the specific surface area, pore volume, and pore size distribution of the materials, crucial for understanding their textural properties.
  • H2 Temperature-Programmed Reduction (H2-TPR): To investigate the reducibility of the SnO2 species, which is related to their catalytic activity.
  • X-ray Photoelectron Spectroscopy (XPS): To determine the chemical states and oxidation states of tin on the catalyst surface.
  • In situ Diffuse Reflectance Infrared Fourier-Transform Spectroscopy (in situ DRIFTS): A key technique to identify reaction intermediates and monitor the CO oxidation process in real-time under reaction conditions.
  • Computational Modeling:
    • Density Functional Theory (DFT) calculations: Used to model the adsorption of CO and O2 on the SnO2 (110) surface and to elucidate the detailed reaction mechanism and energy barriers for CO oxidation.

Datasets

Not discussed in the paper. The study focuses on experimental synthesis and characterization, along with theoretical calculations, rather than training on large datasets.

Key Insights and Ideas

  • KCC-1 as an Ideal Support: The fibrous, flower-like morphology of KCC-1 provides a unique structure that effectively supports highly dispersed, amorphous SnO2 nanoparticles. This morphology is superior to the pore-filling approach seen with MCM-41, which can lead to some agglomeration.
  • Amorphous SnO2 is Key: The SnO2 nanoparticles on KCC-1 were found to be in an amorphous form. This amorphous nature, combined with strong SnO2-KCC-1 interactions, is crucial for enhanced catalytic activity and stability, preventing sintering.
  • Synergistic Interaction: The excellent interaction between the SnO2 nanoparticles and the KCC-1 support plays a vital role in stabilizing the nanoparticles and promoting efficient CO catalytic removal.
  • Mars-van Krevelen Mechanism: The study confirms that CO oxidation on the SnO2 (110) surface follows the Mars-van Krevelen (MvK) mechanism, involving lattice oxygen from the SnO2.
  • Reaction Pathway Elucidation: The combination of in situ DRIFTS and DFT calculations successfully mapped out the sequential steps of CO oxidation, providing a fundamental understanding of the catalytic process.

Key Results

  • High Catalytic Activity: The Sn7@KCC-1 catalyst achieved 90% CO conversion at a low temperature of approximately 175 °C, outperforming pure SnO2 and Sn7@MCM-41.
  • Excellent Stability: The Sn7@KCC-1 catalyst demonstrated remarkable stability, with no significant loss in CO catalytic activity observed after a 25-hour test at 200 °C.
  • Enhanced Reducibility: Snx@KCC-1 catalysts showed a lower reduction temperature (~100 °C lower than pure SnO2), indicating improved redox properties and facilitating CO oxidation.
  • Optimized Sn Loading: While higher SnO2 loading (e.g., Sn10@KCC-1) led to some aggregation and reduced activity, Sn7@KCC-1 represented an optimal balance for high dispersion and performance.
  • DFT Confirmation: DFT calculations revealed favorable adsorption energies for CO and O2 on the SnO2 (110) surface, supporting the experimental findings and providing insights into the reaction mechanism. The calculated energy barrier for CO oxidation was also determined.

Limitations and Future Work

  • Limited Sn Loading Range Explored: While Sn1%, Sn3%, Sn5%, Sn7%, and Sn10% were tested, further exploration of even lower or higher loadings might reveal additional performance nuances.
  • Moisture Sensitivity: While not explicitly stated as a limitation, many CO oxidation catalysts are sensitive to moisture. Future work could investigate the catalyst's performance under humid conditions, which are common in real-world applications.
  • Long-Term Durability: Although 25-hour stability was demonstrated, even longer-term testing under various conditions would further validate its robustness.
  • Broader Application Scope: The study focuses on CO oxidation. Future research could explore the potential of these SnO2@KCC-1 catalysts for other oxidation reactions or as supports for different active metal nanoparticles.
  • Scale-up Potential: Investigating the scalability of the KCC-1 synthesis and the impregnation process for industrial applications would be a logical next step.

Summary updated

Abstract

A large surface area dendritic mesoporous silica material (KCC-1) was successfully synthesized and used as a support to confine SnO2 nanoparticles (NPs). Owing to the large specific surface area and abundant mesoporous structure of dendritic KCC-1, the SnO2 NPs were highly dispersed, resulting in significantly improved CO catalytic oxidation activity. The obtained Snx/KCC-1 catalysts (x represents the mass fraction of SnO2 loading) exhibited excellent CO catalytic activity, with the Sn7@KCC-1 catalyst achieving 90% CO conversion at about 175 °C. The SnO2 NPs on the KCC-1 surface in a highly dispersed amorphous form, as well as the excellent interaction between SnO2 NPs and KCC-1, positively contributed to the catalytic removal process of CO on the catalyst surface. The CO catalytic removal pathway was established through a combination of in situ diffuse reflectance infrared transform spectroscopy and density-functional theory calculations, revealing the sequential steps: ① CO → CO32−ads, ② CO32−ads → CO2free+SnOx−1, ③ SnOx−1+O2 → SnOx+1. This study provides valuable insights into the design of high-efficiency non-precious metal catalysts for CO catalytic oxidation catalysts with high efficiency.
BibTeX
@inproceedings{li2023insights,
  author = {Guobo Li and Yingying Zhang and Jie Yan and Yiwei Luo and Conghui Wang and Weiwei Feng and Shule Zhang and Wenming Liu and Zehui Zhang and Honggen Peng},
  title = {{Insights into SnO2 Nanoparticles Supported on Fibrous Mesoporous Silica for CO Catalytic Oxidation}},
  booktitle = {Catalysts},
  year = {2023},
  doi = {10.3390/catal13081156},
}
Figure