Influence of a low-frequency electromagnetic field on aluminum alloy slabs during horizontal direct chill casting process

Jianzhong Cui, Yudong Zhang, Lei Li, Claude EslingHAL (Le Centre Pour la Communication Scientifique Directe) 2015

TL;DR

This paper investigates how low-frequency electromagnetic fields (LF-EMFs) can improve the quality of 2024 aluminum alloy slabs produced via horizontal direct chill (HDC) casting. They found that applying specific EMF intensities and frequencies significantly refines grain structure and reduces undesirable element segregation, leading to more uniform and higher-quality materials.

What Problem Does This Paper Address?

Direct chill (DC) casting is a widely used method for producing metal ingots. While horizontal DC (HDC) casting offers advantages like lower investment costs and greater flexibility compared to vertical DC (VDC), it suffers from inherent issues like non-uniform microstructures and macro-segregation of alloying elements. This is primarily due to gravity-driven phenomena during solidification, where heavier elements tend to settle and temperature gradients can lead to inconsistent grain growth. The paper aims to address these limitations by exploring the application of low-frequency electromagnetic fields (LF-EMFs) to the HDC process, seeking to mitigate these issues and improve the overall quality of the cast aluminum alloy slabs.

Methods

The researchers employed a horizontal direct chill (HDC) casting setup to produce two slabs of 2024 aluminum alloy. The key experimental variable was the application of low-frequency electromagnetic fields (LF-EMFs).

  • EMF Application: Two experimental conditions were tested:
  • Varying Intensity: The frequency was fixed at 30 Hz, while the EMF intensity was varied from 0 to 15000 Ampere-turns (At).
  • Varying Frequency: The EMF intensity was fixed at 15000 At, while the frequency was varied across 10 Hz, 20 Hz, 30 Hz, and 50 Hz.
  • Sample Preparation: Slices were cut transversely from the cast slabs, and three specimens (top, middle, and bottom) were extracted from each slice for analysis.
  • Microstructural Analysis: Optical microscopy was used to observe the a-Al grain size and morphology.
  • Chemical Analysis: Electron probe microanalysis (EPMA) was used to determine the copper (Cu) concentration profiles across the samples, assessing macro-segregation.

Datasets

Not discussed in the paper. The study relies on experimental data generated from the casting process itself.

Key Insights and Ideas

  • EMF as a Grain Refiner: The application of LF-EMFs demonstrably refines the a-Al grain structure. This is attributed to the Lorentz forces generated within the melt, which induce stirring and fragmentation of dendrites, leading to more numerous and smaller grains.
  • Intensity Matters: Increasing the intensity of the EMF, at a fixed frequency, leads to progressively finer grains and a more homogeneous distribution of alloying elements. This suggests that stronger electromagnetic forces are more effective in counteracting gravity-driven segregation.
  • Frequency Optimization is Crucial: There's an optimal frequency for EMF application. While higher frequencies might concentrate the effect near the surface, very low frequencies may not generate sufficient stirring. The study identifies 30 Hz as the most favorable frequency for both grain refinement and reducing Cu segregation in this specific alloy and process.
  • Homogenization Across the Slab: Without EMF, there's a noticeable difference in grain size between the top and bottom of the slab, with the bottom often having finer grains due to higher cooling rates. LF-EMFs help to equalize grain sizes across the cross-section, leading to more uniform material properties.
  • Counteracting Gravity Segregation: The study confirms that gravity causes Cu to segregate towards the bottom of the slab. LF-EMFs effectively mitigate this by promoting better mixing of the melt, leading to a more even distribution of Cu.

Key Results

  • Grain Refinement: Without EMF, a-Al grains were coarse. With increasing EMF intensity (at 30 Hz), grain size decreased, with 15000 At yielding fine dendritic morphology.
  • Microstructure Uniformity: At 15000 At and 30 Hz, the a-Al grain sizes at the top and bottom positions of the slab became nearly uniform, unlike the non-uniformity observed without EMF.
  • Optimal Frequency: At 15000 At, 30 Hz was found to be the most effective frequency for refining a-Al grains and inhibiting Cu macro-segregation.
  • Cu Segregation Reduction: In all cases, Cu segregation was observed (B > T > M). However, increasing EMF intensity and using the optimal frequency (30 Hz) significantly reduced the concentration differences between these positions, leading to more homogenized Cu distribution.

Limitations and Future Work

  • Limited Alloy Scope: The study focused on 2024 aluminum alloy. The optimal EMF parameters (intensity and frequency) might differ for other aluminum alloys or other casting materials.
  • Specific HDC Configuration: The results are specific to the experimental HDC setup used, including mold dimensions, casting speed, and coil design. Scaling these findings to industrial-scale HDC processes would require further investigation.
  • Future Work: The authors suggest that further research could explore the application of LF-EMFs to other aluminum alloys and investigate the underlying mechanisms of EMF interaction with the melt in more detail. Understanding the precise relationship between EMF parameters and the resulting melt dynamics could lead to more optimized casting processes.

Summary updated

Abstract

International audience
BibTeX
@inproceedings{cui2015influence,
  author = {Jianzhong Cui and Yudong Zhang and Lei Li and Claude Esling},
  title = {{Influence of a low-frequency electromagnetic field on aluminum alloy slabs during horizontal direct chill casting process}},
  booktitle = {HAL (Le Centre Pour la Communication Scientifique Directe)},
  year = {2015},
}
Figure