Influence Analysis of Impeller-Guide Vane Matching on Energy and Pressure Pulsation in a Tubular Pump Device

Lin Zhu, Fan Yang, Xin Xu, Jin Xiao, Min Chen, Guan XuJournal of Applied Fluid Mechanics 2023 · DOI

This study provides a deep dive into the fluid dynamics of shaft tubular pumps—the workhorses of large-scale irrigation and flood control. By analyzing the "handshake" between rotating impeller blades and stationary guide vanes, the researchers reveal how specific blade-number combinations can either optimize energy recovery or trigger problematic vibrations.

TL;DR

This paper investigates how the numerical matching of impeller blades and guide vanes affects the efficiency and stability of tubular pumps. Using advanced Very-Large-Eddy Simulations (VLES), the authors demonstrate that while increasing blade counts generally improves energy efficiency by smoothing out flow distribution, it also introduces higher pressure pulsations and localized flow instabilities.

What Problem Does This Paper Address?

In the world of hydraulic engineering, tubular pumps are prized for their simple structure and low hydraulic loss. However, they face a persistent challenge: Rotor-Stator Interaction (RSI). This is the complex fluid "collision" that occurs when high-speed water exiting the rotating impeller (the rotor) hits the stationary guide vanes (the stator).

If the number of blades on the impeller and the guide vanes aren't matched correctly, the pump can suffer from poor efficiency, hydraulic vibration, and even structural resonance. While previous research has looked at blade shapes, there is a lack of detailed energy-perspective analysis on how simply changing the number of blades in each component alters the internal flow field and pressure stability.

Methods

The researchers employed a multi-pronged theoretical and computational approach:

  • VLES (Very-Large-Eddy Simulation): A hybrid turbulence model that combines the computational efficiency of RANS (near the walls) with the high precision of DNS (in the main flow). This allowed them to capture transient flow structures that standard models might miss.
  • Entropy Generation Theory: Used to pinpoint exactly where energy is being lost to friction and turbulence within the pump.
  • Energy Gradient Theory ($K$ function): A novel method to identify regions of flow instability. A high $K$ value indicates where the flow is likely to become chaotic or "break."
  • Experimental Validation: The team verified their numerical model using a physical high-precision hydraulic machinery test bench, ensuring the simulation's efficiency predictions were within a 3% margin of error.

Datasets

The study did not use external public datasets but generated a comprehensive internal dataset through:

  • Six Calculation Schemes: Combinations of 3 or 4 impeller blades matched with 5, 6, or 7 guide vanes.
  • Experimental Benchmarks: Physical testing of "Scheme 1" (3 impeller blades, 5 guide vanes) across various flow rates ($K_Q$ from 0.34 to 0.59) to provide a baseline for the simulations.

Key Insights and Ideas

  • The Uniformity Paradox: You might expect more blades to cause more friction and lower efficiency. However, the study found that increasing the number of impeller blades from 3 to 4 actually made the flow entering the guide vanes more uniform (reducing non-uniformity by up to 17.4%). This better "alignment" allows the guide vanes to recover energy more effectively.
  • Energy vs. Stability Trade-off: Increasing the impeller blade count gives the water more kinetic energy (higher head), but it also makes the flow at the impeller outlet more unstable. The $K$ function analysis showed that the 4-blade impeller creates significantly more turbulence than the 3-blade version.
  • The Guide Vane as a "Buffer": While the 4-blade impeller creates more initial instability, a higher number of guide vanes (e.g., 7 vanes) acts as a superior energy recovery system. It effectively "tames" the chaotic flow, bringing the pressure pulsations back down to levels comparable to simpler, less efficient designs.

Key Results

  • Efficiency Gains: Scheme 6 (4 impeller blades, 7 guide vanes) emerged as the top performer. The maximum efficiency difference between the best and worst configurations was approximately 4%.
  • Head Increase: At low flow rates, moving from 3 to 4 impeller blades increased the pump head by a staggering 23.6%.
  • Pressure Pulsations: Scheme 6 showed higher vibration amplitudes at the impeller outlet (specifically at the blade frequency), but these pulsations were successfully mitigated by the time the water reached the guide vane outlet.
  • Loss Localization: Entropy maps revealed that the highest energy losses occur at the trailing edges of the blades due to flow separation—a critical area for future geometric optimization.

Limitations and Future Work

The authors acknowledge that while blade number is a critical variable, it is only one piece of the puzzle.

  • Geometry Constraints: The study kept blade thickness and specific curvature profiles constant. Future work could explore the "co-optimization" of blade number and blade twist angles.
  • Flow Conditions: The analysis focused heavily on steady-state and standard operating conditions. Investigating extreme "off-design" conditions (like very low flow or start-stop cycles) would be valuable for real-world pump station longevity.
  • Structural Coupling: While pressure pulsations were measured, the paper does not perform a full Fluid-Structure Interaction (FSI) analysis to see how these pulsations translate into actual mechanical fatigue over years of operation.

Summary updated

Abstract

Tubular pump devices offer advantages such as low hydraulic losses, a simple structure, and easy maintenance. They find extensive application in areas such as irrigation, flood control, and water diversion. The performance and security of the pump are directly impacted by the contact between the impeller and guide vane. The matching relationship between the number of impeller blades and guide vanes significantly influences this interaction in tubular pump devices. To explore this impact, a Very-Large-Eddy Simulation turbulence model was employed to simulate the 3D flow fields of six different number matching relationships in a shaft tubular pump device. The analysis focused on the energy performance of the different schemes, the flow distribution of the guide vanes, and the velocity circulation at the guide vanes’ outlet. Entropy theory and energy gradient theory were employed to understand how the number matching relationship influences energy performance. Additionally, pressure pulsations were analyzed at the impeller and guide vanes for different matching configurations. The results indicate that although increasing the number of impeller blades can lead to higher water circulation, increased energy, and potentially unstable water flow, an increase in impeller blades number results in improved flow distribution in each guide vane groove, leading to an overall enhancement in the efficiency of the pump device. Similarly, increasing the number of guide vanes may increase the non-uniformity of the guide vane flow rate, but it also enhances the ability of the guide vanes to regulate water circulation and recover energy, thereby benefiting the overall efficiency.
BibTeX
@article{zhu2023influence,
  author = {Lin Zhu and Fan Yang and Xin Xu and Jin Xiao and Min Chen and Guan Xu},
  title = {{Influence Analysis of Impeller-Guide Vane Matching on Energy and Pressure Pulsation in a Tubular Pump Device}},
  journal = {Journal of Applied Fluid Mechanics},
  year = {2023},
  doi = {10.47176/jafm.16.11.1973},
}
Figure