Implementation of a Phase Synchronization Scheme Based on Pulsed Signal at Carrier Frequency for Bistatic SAR

Yafeng Chen, Da Liang, Haixia Yue, Dacheng Liu, Xiayi Wu, Heng Zhang, Yuanbo Jiao, Kaiyu Liu, Robert WangSensors 2020 · DOI

TL;DR

This paper introduces a novel phase synchronization scheme for bistatic synthetic aperture radar (BiSAR) systems using a pulsed signal at the carrier frequency. This method offers a simpler, more reliable, and non-interrupted synchronization process compared to existing linear frequency modulation (LFM) approaches, crucial for accurate topographic mapping with BiSAR.

What Problem Does This Paper Address?

Bistatic synthetic aperture radar (BiSAR) systems, where the transmitter and receiver are on different platforms, offer unique advantages like flexible baseline configurations and cost savings. A key challenge in BiSAR, especially for interferometric applications like generating digital elevation models (DEMs), is achieving precise phase synchronization between the transmitting (primary) and receiving (slave) satellites. Inaccurate phase synchronization leads to significant errors in the final imagery and DEMs. Existing methods, like those used in the TanDEM-X mission, rely on LFM signals, which can be complex to implement and may not be ideal for all scenarios. This paper addresses the need for a more robust, simpler, and non-interrupted phase synchronization scheme for BiSAR systems.

Methods

The core of this paper is the proposed Pulsed Signal at Carrier Frequency (PSCF) phase synchronization scheme. Instead of using a complex LFM signal, this method utilizes a simple pulsed signal transmitted at the radar's carrier frequency. The synchronization is achieved through an exchange strategy where the primary satellite transmits a synchronization pulse to the slave satellite in one pulse repetition time (PRT), and vice-versa in the next PRT. This ensures the normal radar operation is not interrupted.

The extracted synchronization pulses are processed using Fast Fourier Transform (FFT) to perform pulse compression and extract the peak phase information. This phase information is then used to calculate a compensation phase. This compensation phase is applied point-by-point to the slave satellite's echo data to correct for phase differences and achieve synchronization. The paper also includes a theoretical analysis comparing the Signal-to-Noise Ratio (SNR) of the PSCF signal with that of an LFM signal, demonstrating they can achieve similar SNRs.

Datasets

The paper describes experiments conducted using a ground validation system called LuTan-1. This system simulates a bistatic SAR environment within a microwave anechoic chamber. No specific public datasets were used; rather, the system itself served as the experimental platform for data collection and validation.

Key Insights and Ideas

  • Simplicity and Robustness: The PSCF scheme offers a significantly simpler hardware implementation and signal processing compared to LFM-based methods, leading to improved system reliability.
  • Non-Interrupted Operation: The time-slot exchange strategy for synchronization pulses ensures that the primary radar data acquisition is not disrupted, which is a key advantage for continuous operation.
  • FFT for Rapid Extraction: Utilizing FFT for pulse compression and phase extraction is an efficient method for rapidly obtaining the necessary synchronization information.
  • Comparable SNR: Theoretical analysis shows that a pulsed signal at carrier frequency can achieve a comparable SNR to an LFM signal, suggesting comparable performance in terms of signal quality.
  • Guiding Significance: The findings have direct implications for the design of future bistatic and multistatic SAR systems, offering a practical and effective synchronization solution.

Key Results

The paper presents experimental results from the LuTan-1 ground validation system.

  • The PSCF scheme achieved a residual phase standard deviation (STD) of 0.780° and a peak-peak value of 1.139°.
  • In comparison, the LFM-phase signal scheme resulted in a residual phase STD of 0.978° and a peak-peak value of 0.524°. While the LFM scheme showed slightly better short-term performance (lower peak-peak value), the PSCF scheme's residual phase STD was still within acceptable limits for BiSAR applications. The paper highlights that the PSCF scheme's advantages in system design simplicity and reliability are significant.

Limitations and Future Work

  • Short-Term Startup Performance: The paper notes that the PSCF scheme is "slightly worse than the linear frequency modulation during the short-term startup of the BiSAR." This suggests that while it meets accuracy requirements, there might be a slight performance dip during initial acquisition compared to LFM.
  • Ground Validation: The experiments were conducted on a ground validation system. While this provides a controlled environment, real-world spaceborne conditions (e.g., atmospheric effects, longer baselines) might introduce additional challenges.
  • Future Work: The paper implies that this scheme has "guiding significance for the synchronization design of bistatic and multistatic SAR systems," suggesting its applicability and potential for further refinement in more complex multi-satellite configurations. The authors also mention that the PSCF scheme can "fulfill the synchronization accuracy requirement for the BiSAR system," indicating its readiness for practical implementation.

Summary updated

BibTeX
@article{chen2020implementation,
  author = {Yafeng Chen and Da Liang and Haixia Yue and Dacheng Liu and Xiayi Wu and Heng Zhang and Yuanbo Jiao and Kaiyu Liu and Robert Wang},
  title = {{Implementation of a Phase Synchronization Scheme Based on Pulsed Signal at Carrier Frequency for Bistatic SAR}},
  journal = {Sensors},
  year = {2020},
  doi = {10.3390/s20113188},
}

Loading related content...

Figure