Abstract
In deep-well drilling operations, maintaining the rheological stability of drilling fluids under high-temperature and high-pressure (HTHP) conditions is critical for effective hole cleaning and formation protection. This study investigates the performance of Driscal-D, a synthetic polymer treating agent, under conditions up to 220°C. Using a Fann 50SL rheometer, the research evaluates the influence of polymer concentration, various electrolytes (inorganic and organic salts), clay types (bentonite, sepiolite, attapulgite), and antioxidants on fluid viscosity and shear stress. Results indicate that while extreme temperatures significantly degrade viscosity, the addition of organic formates and antioxidants can mitigate these effects. Furthermore, the incorporation of bentonite clay enhances the fluid's pseudoplastic behavior, which is best characterized by the Herschel–Bulkley model.
Introduction
The "mud" or drilling fluid serves as the lifeblood of deep-well oil and gas drilling, tasked with transporting rock cuttings to the surface. To function effectively, these fluids must exhibit pseudoplastic (shear-thinning) properties—remaining thick enough to suspend cuttings but thinning sufficiently under pump pressure for easy circulation. However, the extreme HTHP environments of deep wells often cause polymers to degrade, leading to a loss of viscosity and a transition toward Newtonian behavior. This study systematically examines how different additives interact with the Driscal-D polymer to maintain functional rheology above 200°C.
Methods
The experimental framework utilized Driscal-D, a sulfonated copolymer (2-acrylamido-2-methylpropane sulfonic acid sodium salt). Rheological measurements were conducted using a Fann 50SL HTHP Rheometer across a temperature range of 40°C to 220°C at a constant pressure of 1000 psi.
Key experimental variables included:
- Polymer Concentration: 0.75% to 2.0% (w/v).
- Electrolytes: Comparison between inorganic salts (NaCl, KCl, CaSO₄) and organic salts (Sodium and Potassium Formates).
- Clay Additives: Bentonite (NV-1), Sepiolite (SEP), and Attapulgite (ATTP).
- Antioxidants: Sodium sulfite (Na₂SO₃) was employed as an oxygen scavenger.
Data were fitted to the Power Law and Herschel–Bulkley mathematical models to determine yield points and flow behavior indices.
Results and Discussion
Temperature and Concentration Effects
Pure polymer solutions experienced a drastic viscosity reduction of 74% to 94% when heated from 40°C to 220°C. Higher polymer concentrations generally increased initial viscosity and pseudoplasticity, though the thinning effect of heat remained the dominant factor.
Electrolyte Interactions and the "Curling" Effect
The study observed a "curling" effect where cations (Na⁺, Ca²⁺) neutralized polymer chain charges, causing them to coil and reducing their hydrodynamic volume. Divalent ions like Ca²⁺ were particularly detrimental, leading to polymer precipitation. Conversely, organic formates (NaCOOH/HCOOK) acted as thermal shields, stabilizing the water structure around the polymer and allowing for a 50% viscosity recovery rate upon cooling.
Oxidative Protection
At high temperatures, dissolved oxygen triggers free-radical degradation of the polymer backbone. The addition of sodium sulfite significantly preserved viscosity at low shear rates (< 50 s⁻¹), which is vital for suspending cuttings during pump downtime.
Clay Synergy
The addition of clay, particularly bentonite, created a structural network that enhanced shear stress. These mixtures followed the Herschel–Bulkley model, providing the necessary yield stress for efficient cuttings transport. The performance ranking for clays was determined to be: Bentonite > Sepiolite > Attapulgite.
Conclusion
This research demonstrates that while HTHP conditions pose a severe threat to polymer-based drilling fluids, strategic chemical engineering can preserve their functionality. The use of organic formates and antioxidants provides a robust defense against thermal and oxidative degradation, while bentonite clay ensures the structural integrity required for deep-well operations. Future studies should address higher pressure regimes and the interactions of these additives within more complex, multi-component mud systems.
Summary updated