TL;DR
This paper presents a numerical study of a novel combined offshore wind and wave energy structure, integrating a 5-MW semisubmersible wind turbine with a heave-type wave energy converter (WEC). The research aims to optimize the design and understand the hydrodynamic performance of this integrated system, paving the way for more efficient and cost-effective offshore renewable energy generation.
What Problem Does This Paper Address?
The world is increasingly looking towards renewable energy sources to combat climate change and energy crises. Offshore wind energy has seen significant development, but faces challenges in commercial viability. Wave energy, while abundant, is still in its early stages. Combining these two technologies into a single structure offers a promising solution to improve energy output, share infrastructure, and reduce costs. However, designing and analyzing such complex, multi-body floating structures presents significant engineering challenges, particularly in understanding their dynamic behavior under various sea conditions. This paper addresses the need for a comprehensive hydrodynamic analysis of a specific combined wind-wave energy structure to inform its design and predict its performance.
Methods
The researchers developed a numerical model using ANSYS/AQWA, a widely used tool for hydrodynamic analysis. They employed potential flow theory to model the wave loads on the structure, assuming an ideal, incompressible fluid. For the semisubmersible platform's columns, which are considered smaller diameter elements, the Morison equation was used to account for viscous drag forces in the horizontal direction. A crucial aspect of the study was the inclusion of viscous effects specifically for the WEC's heave motion, as potential flow theory alone can overestimate power output. The equation of motion for the combined structure was formulated in the time domain, incorporating linear excitation forces, added mass, potential damping, and mechanical coupling (PTO system) between the two bodies. They also investigated the impact of hydrodynamic coupling between the semisubmersible and the WEC, which accounts for the interaction of their radiation and diffraction potentials.
Datasets
Not discussed in the paper. The study relies on simulated sea conditions rather than real-world datasets for training or evaluation.
Key Insights and Ideas
- Synergy is Key: Combining wind and wave energy in a single structure isn't just about co-location; it's about leveraging shared infrastructure and potentially enhancing overall energy capture efficiency.
- WEC Design Matters: The outer diameter and draft of the WEC significantly influence its performance and the overall structure's safety. A diameter of 16m and a draft of 3.5m were found to be optimal for balancing cost, safety, and power generation.
- PTO Tuning is Crucial: The damping coefficient (BPTO) of the Power Take-Off (PTO) system is critical for maximizing wave energy capture. A value of 1500 kNs/m was identified as optimal for the studied configuration.
- Viscosity Can't Be Ignored (for WEC): While potential flow theory is a good starting point, ignoring viscous effects in the WEC's heave motion can lead to overestimation of produced power.
- Hydrodynamic Coupling is Significant for WEC: The interaction between the semisubmersible and the WEC's fluid dynamics (hydrodynamic coupling) has a more pronounced effect on the WEC's responses (especially diffraction and radiation forces) than on the semisubmersible itself. This suggests that WEC design and analysis need careful consideration of this coupling.
- Survival Mode is Essential: In extreme sea conditions, mechanically locking the WEC to the semisubmersible is a viable strategy for survival, significantly reducing relative motion and mitigating extreme loads.
Key Results
- The optimal WEC outer diameter was determined to be 16m, and the draft was set at 3.5m to avoid slamming effects.
- A preliminary best-fit PTO damping coefficient (BPTO) of 1500 kNs/m was identified for maximizing wave energy production.
- The study demonstrated that viscous effects on the WEC's heave motion lead to reduced produced power compared to potential flow analysis alone.
- Hydrodynamic coupling significantly increased diffraction and radiation forces on the WEC (up to 52.2% and 55.4% respectively) compared to the semisubmersible.
- Under regular waves, responses like relative heave and pitch showed a near-linear relationship with wave height, while WEC surge and PTO power exhibited an approximately quadratic relationship.
- In extreme sea conditions (LC4), the locked mode resulted in a maximum heave motion of approximately 6m, highlighting the importance of survival strategies.
Limitations and Future Work
The authors acknowledge that this study is a first stage, focusing on the dynamic response and geometry optimization. Future work should include:
- Experimental Validation: The numerical model needs to be validated against physical model tests to confirm its accuracy.
- Further Optimization: While a rational value for the PTO damping coefficient was found, a full mathematical optimization problem was not solved.
- Wind Loads: While wind loads were considered in some irregular wave scenarios, their full integration and impact on the combined structure's dynamics, especially in extreme conditions, could be further explored.
- Survival Models: The paper suggests exploring other survival models beyond the mechanical locking of the WEC.
- Cost-Benefit Analysis: A more detailed economic analysis considering the trade-offs between cost reduction and safety would be beneficial.
Summary updated