Hybrid ZnO Electron Transport Layer by Down Conversion Complexes for Dual Improvements of Photovoltaic and Stable Performances in Polymer Solar Cells

Fanchen Bu, Wenfei Shen, Xiaolin Zhang, Yao Wang, Laurence A. Belfiore, Jianguo TangNanomaterials 2020 · DOI

TL;DR

This paper introduces a novel hybrid electron transport layer (ETL) for polymer solar cells (PSCs) by incorporating lanthanide down-conversion complexes (Eu(TTA)₃phen, ETP) into a ZnO ETL. This approach effectively broadens the spectral response of PSCs into the UV region and significantly enhances their operational stability against UV degradation, leading to improved power conversion efficiencies.

What Problem Does This Paper Address?

Polymer solar cells (PSCs) hold great promise for flexible, low-cost energy generation, but two major hurdles hinder their widespread adoption: a limited spectral response range, primarily in the visible light spectrum, and susceptibility to degradation from ultraviolet (UV) radiation. The inability to efficiently utilize UV light means a significant portion of the solar spectrum is wasted, while UV exposure can break down the organic materials, leading to a decline in performance and device lifetime. Existing solutions, like UV-cut filters, often reduce overall light intensity, impacting efficiency. Therefore, there's a critical need for strategies that can both capture and utilize UV light while simultaneously protecting the active materials from its damaging effects.

Methods

The researchers developed a hybrid ZnO/ETP electron transport layer by introducing Eu(TTA)₃phen (ETP) complexes into a ZnO precursor solution. This mixture was then spin-coated onto ITO substrates to form the ETL. The ETP complexes, known for their ability to absorb UV light and re-emit it in the visible spectrum, were integrated into the ZnO layer. The study employed a range of characterization techniques to understand the material properties and device performance:

  • X-ray Photoelectron Spectroscopy (XPS): To analyze the elemental composition and chemical states of the ZnO and ZnO/ETP films.
  • Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM): To investigate the surface morphology and topography of the films.
  • Photo-induced Force Microscopy (PiFM): To map the spatial distribution of chemical compositions within the films.
  • Fourier Transform Infrared (FTIR) Spectroscopy: To identify functional groups and chemical bonds.
  • Transmission Electron Microscopy (TEM) and Energy Dispersive Spectroscopy (EDS): To examine the structure and elemental distribution of the ETP complexes and the hybrid film.
  • Current Density-Voltage (J-V) Measurements: To evaluate the photovoltaic performance (PCE, Voc, Jsc, FF) under simulated solar illumination.
  • External Quantum Efficiency (EQE) Measurements: To assess the spectral response and efficiency across different wavelengths.
  • Thermogravimetric Analysis (TGA): To determine the thermal stability of the ETP complexes.
  • UV-Vis Spectroscopy: To analyze the optical absorption and transmittance properties.
  • Stability Testing: Devices were exposed to ambient conditions to evaluate their long-term performance decay.

Datasets

Not discussed in the paper. The study focuses on experimental device fabrication and characterization using commercially available materials.

Key Insights and Ideas

  • UV Harvesting and Down-Conversion: The ETP complexes act as "UV sponges," absorbing high-energy UV photons and re-emitting them as lower-energy visible photons. This down-conversion process is crucial because the re-emitted visible light aligns well with the absorption spectra of the active layer materials (PTB7-Th and PBDB-T-2F), effectively extending the usable solar spectrum.
  • Nanostructure Control for Performance: By carefully controlling the concentration of ETP complexes within the ZnO ETL, the researchers were able to manipulate the nanostructure morphology. This fine-tuning prevented large aggregations of ETP, which could disrupt the device's fine structure and lead to recombination losses. Instead, a uniform dispersion was achieved, optimizing charge transport.
  • Defect Passivation: Incorporating ETP complexes into the ZnO ETL helped to reduce oxygen vacancies in the ZnO film. These vacancies can act as recombination centers, negatively impacting device performance. By filling these vacancies, the ETP contributes to improved charge collection and higher fill factors.
  • Synergistic Stability Enhancement: The ETP layer not only harvests UV light but also acts as a protective shield, reducing the direct impact of UV radiation on the sensitive organic active layer materials. This dual function significantly prolongs the operational lifetime of the solar cells.

Key Results

  • Enhanced Power Conversion Efficiency (PCE):
    • For PTB7-Th–PC71BM devices, the ZnO/ETP ETL achieved a PCE of 9.22%, a 13.7% increase compared to the ZnO-only device (8.11%).
  • For PBDB-T-2F–IT-4F devices, the ZnO/ETP ETL achieved a PCE of 13.12%.
  • Improved Short-Circuit Current Density (Jsc): The ZnO/ETP devices showed higher Jsc values, attributed to the broader spectral response and enhanced light absorption.
  • Increased Fill Factor (FF): The FF improved significantly in ZnO/ETP devices (e.g., from 62.22% to 68.13% for PTB7-Th–PC71BM devices), likely due to reduced charge recombination thanks to defect passivation.
  • Prolonged Device Stability: The stability of PTB7-Th–PC71BM devices with the ZnO/ETP layer was prolonged by 70% compared to devices with a pure ZnO ETL, maintaining a normalized efficiency of 65% after 17 days, while the reference device degraded to 0%.

Limitations and Future Work

  • Concentration Optimization: While the study identified an optimal concentration for ETP (5 × 10⁻³ mol/L), further exploration of concentration effects and potential aggregation issues at higher concentrations might be beneficial.
  • Material Compatibility: The study focused on specific polymer donor-acceptor pairs (PTB7-Th–PC71BM and PBDB-T-2F–IT-4F). Future work could investigate the applicability of this hybrid ETL with a wider range of organic photovoltaic materials.
  • Scalability and Cost: While the solution-based method is promising, the cost and scalability of synthesizing and incorporating ETP complexes for large-scale manufacturing would need to be considered.
  • Long-Term Encapsulated Stability: The stability tests were performed on unencapsulated devices in an N2-filled glove box. Investigating the stability of encapsulated devices under real-world conditions would be crucial for practical applications.

The authors suggest that this approach of incorporating down-conversion materials into ETLs offers a promising avenue for designing high-performance and stable polymer solar cells.

Summary updated

Abstract

Polymer solar cells (PSCs) have shown excellent photovoltaic performance, however, extending the spectral response range to the ultraviolet (UV) region and enhancing the UV light stability remain two challenges to overcome in the development of PSCs. Lanthanide down-conversion materials can absorb the UV light and re-emit it at the visible region that matches well with the absorption of the active layer material PTB7-Th (poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbony]thieno[3,4-b]thiophenediyl]]) and PBDB-T-2F, thus helping to enhance the photovoltaic performance and UV light stability of PSCs. In this research, a down-conversion material Eu(TTA)<sub>3</sub>phen (ETP) is introduced into the cathode transport layer (ZnO) in PSCs to manipulate its nanostructure morphology for its application in hyperfine structure of PSCs. The device based on the ZnO/ETP electron transport layer can obtain power conversion efficiencies (PCEs) of 9.22% (PTB7-Th-PC<sub>71</sub>BM ([6,6]-phenylC<sub>71</sub>-butyric acid methyl ester) device) and 13.12% (PBDB-T-2F-IT-4F device), respectively. Besides, in the research on PTB7-Th-PC<sub>71</sub>BM device, the stability of the device based on ZnO/ETP layer is prolonged by 70% compared with the ZnO device. The results suggest that the ZnO/ETP layer plays the role of enhanced photovoltaic performance and prolonged device stability, as well as reducing photo-loss and UV degradation for PSCs.
BibTeX
@inproceedings{bu2020hybrid,
  author = {Fanchen Bu and Wenfei Shen and Xiaolin Zhang and Yao Wang and Laurence A. Belfiore and Jianguo Tang},
  title = {{Hybrid ZnO Electron Transport Layer by Down Conversion Complexes for Dual Improvements of Photovoltaic and Stable Performances in Polymer Solar Cells}},
  booktitle = {Nanomaterials},
  year = {2020},
  doi = {10.3390/nano10010080},
}
Figure