Humidity Sensing Properties of Paper Substrates and Their Passivation with ZnO Nanoparticles for Sensor Applications

Georgios Niarchos, Georges Dubourg, Georgios Afroudakis, Markos Georgopoulos, Vasiliki Tsouti, Eleni Makarona, Vesna Crnojevic-Bengin, Christos Tsamis2017 · DOI

TL;DR

This paper presents a low-cost method for creating paper-based humidity sensors by passivating the paper substrate with zinc oxide (ZnO) nanoparticles. This approach effectively reduces the paper's inherent sensitivity to humidity, paving the way for the development of disposable and selective gas sensors that are not affected by ambient moisture.

What Problem Does This Paper Address?

Paper, a readily available and inexpensive material, has emerged as a promising substrate for various electronic devices, including sensors. Its porous structure and ability to absorb moisture make it a natural candidate for humidity sensing. However, this very property of moisture absorption can be a significant drawback, affecting the performance and selectivity of other types of sensors fabricated on paper. The challenge, therefore, is to leverage paper's advantages as a substrate while mitigating its susceptibility to humidity, especially for applications where precise gas detection is required without interference from ambient moisture.

Methods

The researchers employed a two-step approach. First, they fabricated paper-based microdevices with interdigitated electrodes (IDEs) using a mask-less laser patterning method on different types of commercial printing paper (plain and glossy). This allowed them to characterize the intrinsic humidity sensing behavior of the paper substrates themselves.

The second, and more novel, step involved passivating the paper substrates with zinc oxide (ZnO) nanoparticles. They synthesized ZnO nanoparticles using a cost-effective sol-gel method and then applied them to the paper substrates via successive spin-coating. The number of ZnO layers was varied to investigate its effect on humidity passivation. The electrical resistance of the devices was measured under controlled relative humidity (RH) levels to evaluate the sensing performance and the effectiveness of the ZnO passivation. Scanning Electron Microscopy (SEM) and Energy-dispersive X-ray spectroscopy (EDX) were used for structural and compositional characterization.

Datasets

Not discussed in the paper. The study focuses on experimental characterization using custom-built setups and commercially available paper substrates.

Key Insights and Ideas

  • Paper's Dual Nature: Paper's porous structure makes it a good candidate for humidity sensing but also a challenge for other gas sensors due to moisture interference.
  • Morphology Matters: The surface morphology of the paper (rough and porous vs. smooth and compact) significantly influences its water absorption and, consequently, its humidity sensing response. Plain paper, with its rougher surface, showed higher sensitivity and faster response times compared to glossy paper.
  • ZnO as a Passivator: ZnO nanoparticles, when applied as successive layers, effectively "passivate" the paper substrate against humidity. They act as a barrier, preventing water molecules from interacting with the cellulose fibers and altering the electrical properties of the device.
  • Layer-by-Layer Control: The degree of humidity passivation can be controlled by the number of ZnO nanoparticle layers deposited. More layers lead to greater passivation.
  • Low-Cost and Disposable Potential: The use of common printing paper and a simple sol-gel spin-coating method for ZnO deposition makes this approach highly suitable for developing low-cost and disposable sensors.

Key Results

  • Uncoated plain paper devices exhibited a significant drop in resistance with increasing humidity from 20% to 70% RH, indicating its inherent humidity sensing capability.
  • Plain paper showed faster response and recovery times compared to glossy paper, attributed to its rougher and more porous surface.
  • Successive spin-coating of ZnO nanoparticles on the paper substrates led to a decrease in the device's response to humidity.
  • After 10 deposited layers of ZnO nanoparticles, the glossy paper devices showed near-complete passivation to humidity in the tested RH range (20-70%).
  • The ZnO passivation layer was found to be stable over a period of 6 months, with minimal variation in measurements.

Limitations and Future Work

  • Long-Term Stability: While short-term stability was investigated, the paper acknowledges that long-term stability is an important factor for paper-based electronics, especially for applications beyond agricultural use. However, they note that their tests over 6 months showed only little variation.
  • Humidity Range: The study focused on the 20% to 70% RH range. Further investigation into higher or lower humidity levels might be beneficial.
  • Specific Gas Detection: The primary goal of this work was humidity passivation. Future work is planned to utilize these ZnO-passivated paper substrates for the detection of specific volatile organic components (VOCs) like ethanol, aiming for selective gas sensors.
  • Mechanism of Passivation: While the effect of ZnO nanoparticles as a barrier is demonstrated, a deeper understanding of the precise interaction mechanisms at the nanoscale could further optimize the process.

Summary updated

BibTeX
@misc{niarchos2017humidity,
  author = {Georgios Niarchos and Georges Dubourg and Georgios Afroudakis and Markos Georgopoulos and Vasiliki Tsouti and Eleni Makarona and Vesna Crnojevic-Bengin and Christos Tsamis},
  title = {{Humidity Sensing Properties of Paper Substrates and Their Passivation with ZnO Nanoparticles for Sensor Applications}},
  year = {2017},
  doi = {10.3390/s17030516},
}

Loading related content...

Figure