Hot Work Mold Repaired via Hot Isostatic Pressing towards High Red Hardness

Xueyuan Ge, Qingxian Ma, Yunbo Chen, Miaohui Wang, Qipeng HuMetals 2023 · DOI

TL;DR

This paper presents a novel method for repairing damaged H13 hot work molds using PM23 high-speed steel powder and Hot Isostatic Pressing (HIP). The study demonstrates that this HIP-based repair, especially when combined with sandblasting pretreatment, significantly enhances the red hardness and tensile strength of the repaired molds, extending their lifespan and reducing production costs.

What Problem Does This Paper Address?

Hot work molds are critical components in various industries, but they are prone to wear, corrosion, and fatigue, leading to costly failures and material waste. Traditional repair methods often create heat-affected zones, leading to localized deformation and are unsuitable for large-area repairs. This paper addresses the challenge of effectively and efficiently repairing these high-value molds to restore their performance and extend their service life, specifically focusing on improving their "red hardness" – their ability to retain hardness at elevated temperatures, a crucial property for hot work applications.

Methods

The researchers employed a multi-faceted approach:

  • Hot Isostatic Pressing (HIP): This powder metallurgy technique was used to consolidate PM23 high-speed steel powder onto damaged H13 mold steel. HIP allows for the bonding of dissimilar materials and the production of dense, defect-free components.
  • Surface Pretreatment: Two surface states of the H13 mold were investigated: a machined state (MS) and a sandblasted state (SS). Sandblasting was used to create a rougher, more receptive surface for the PM23 powder.
  • Heat Treatment: After HIP, the repaired molds underwent a specific heat treatment process involving austenitization and triple tempering to optimize their microstructure and mechanical properties.
  • Microstructural Characterization: Scanning Electron Microscopy (SEM), Electron Backscatter Diffraction (EBSD), and X-ray Diffraction (XRD) were used to analyze the microstructure, phase composition, grain boundaries, and elemental distribution at the interface between the H13 and PM23 materials.
  • Mechanical Property Testing: A suite of tests was conducted, including Vickers hardness (at room temperature and elevated temperatures – "red hardness"), tensile strength, bending strength, and impact toughness, to quantitatively assess the performance of the repaired regions.

Datasets

Not discussed in the paper. The study focuses on experimental material processing and characterization rather than machine learning or data-driven approaches.

Key Insights and Ideas

  • Sandblasting is Key for Bonding: The sandblasted surface (SS) demonstrated superior bonding characteristics compared to the machined surface (MS). The rougher, more irregular surface created by sandblasting likely provided better mechanical interlocking and a larger surface area for diffusion bonding during HIP.
  • HIP Achieves High Density: The HIP process effectively consolidated the PM23 powder, resulting in high-density repaired regions with minimal porosity, crucial for mechanical integrity.
  • Microstructure Dictates Properties: The study meticulously linked microstructural features (carbide distribution, grain boundaries, phase transformations) to the observed mechanical properties, providing a fundamental understanding of the repair mechanism.
  • Red Hardness is Significantly Enhanced: The repaired regions, particularly the PM23-rich areas, exhibited excellent red hardness, retaining significant hardness even after prolonged exposure to elevated temperatures (550 °C). This is a critical finding for hot work applications.
  • Defect Analysis is Crucial: The identification of microcracking due to poor bonding of fine powders and powder boundary microporosity highlights areas for optimization in future repair strategies.

Key Results

  • Tensile Strength: The sandblasted (SS) repaired region achieved a tensile strength of approximately 1195.42 MPa, outperforming the machined (MS) region (1158.67 MPa).
  • Hardness: The repaired region exhibited a hardness of around 672.8 HV at room temperature. The red hardness test showed the PM23 region maintained the highest hardness, with values remaining close to 600 HV even after 960 minutes at 550 °C.
  • Bending Strength: The SS sample showed a significantly higher bending strength (420.19 MPa) compared to the MS sample (345.33 MPa).
  • Impact Toughness: Both MS and SS samples showed comparable impact toughness, with the SS sample slightly higher (70 J vs. 65 J).
  • Microstructure: The sandblasted interface was more irregular and jagged, with a higher density of nanoscale carbides and more low-angle grain boundaries compared to the machined interface.

Limitations and Future Work

  • Powder Size Optimization: The paper identifies microcracking and microporosity as defects. Optimizing the powder particle size of the PM23 material is suggested as a means to improve the repair method and mitigate these issues.
  • Mold Failure Analysis: While cracks were observed, the study notes that the failure mode primarily originated from cracking within the PM23 region, often along carbide expansion in the H13 mold. Further investigation into the precise crack initiation and propagation mechanisms could lead to more robust repairs.
  • Broader Application: While the study focuses on H13 molds, exploring the applicability of this HIP and sandblasting approach to other hot work tool steels or for different types of mold damage could be a valuable future direction.
  • Long-Term Performance: While red hardness was tested over time, long-term service performance under actual hot work conditions would be a logical next step to validate the repair's durability.

Summary updated

Abstract

Repairing hot work molds can extend their lifespans and reduce the production costs. This study presents a proposed method for enhancing the red hardness and strength of repaired molds. The method involves utilizing PM23 high-speed steel powder to repair H13 steel molds with two distinct surface states through the process of hot isostatic pressing (HIP). The internal microstructure changes, bonding state, fracture morphology, and crack extension behaviors of the repaired molds are characterized using scanning electron microscopy and electron backscatter diffraction technology. Additionally, the mechanical properties, including red hardness and tensile strength, are quantitatively analyzed. The findings indicate that the repaired area in the sandblasted sample exhibits a rough and uneven structure, demonstrating exceptional toughness. The tensile strength of the repaired region is approximately 1195.42 MPa, while the hardness measures around 672.8 HV. These properties effectively enhance the performance of the molds. The experimental findings indicate that HIP can effectively restore molds, resulting in enhanced red hardness and improved toughness, particularly when combined with sandblasting as a pretreatment method.
BibTeX
@inproceedings{ge2023hot,
  author = {Xueyuan Ge and Qingxian Ma and Yunbo Chen and Miaohui Wang and Qipeng Hu},
  title = {{Hot Work Mold Repaired via Hot Isostatic Pressing towards High Red Hardness}},
  booktitle = {Metals},
  year = {2023},
  doi = {10.3390/met13101783},
}
Figure