Homoscatter: Towards efficient connectivity for ZigBee backscatter system

Zhaoyuan Xu, Wei GongarXiv 2021 · OpenReview

TL;DR

This paper introduces Homoscatter, a novel backscatter communication system designed for ZigBee devices. By leveraging existing ZigBee hardware for both the exciting signal and the backscatter tag, Homoscatter achieves more efficient, bidirectional communication with significantly reduced spectral leakage compared to prior art. This work paves the way for ultra-low power, highly integrated IoT connectivity.

What Problem Does This Paper Address?

The Internet of Things (IoT) is rapidly expanding, demanding wireless connectivity that is both extremely low-power and efficient. Backscatter communication offers a promising solution for ultra-low power devices, as the backscatter tag itself requires minimal power to operate. However, existing ZigBee-compatible backscatter systems, like Interscatter, suffer from significant drawbacks. Interscatter uses Bluetooth as an exciting source, making it a one-way communication system and limiting its ability to decode ZigBee packets. Furthermore, its modulation technique, instantaneous phase change, creates substantial spectral leakage, interfering with neighboring channels. This paper aims to overcome these limitations by developing a homogeneous ZigBee backscatter system that is efficient, bidirectional, and spectrally clean.

Methods

Homoscatter introduces several key innovations:

  • Homogeneous ZigBee Excitation: Instead of relying on non-ZigBee devices like Bluetooth, Homoscatter utilizes specific ZigBee chips to generate the exciting RF signal. This allows for seamless integration with existing ZigBee networks and enables bidirectional communication.
  • Single-Tone Modulation with Continuous Phase Change: To address the spectral leakage issue of Interscatter, Homoscatter uses a single-tone excitation and modulates information through continuous phase changes. This technique, termed FP-OQPSK, significantly narrows the backscattered signal's spectrum.
  • Codeword Translation on Packet Header: To maximize the utilization of the exciting signal, Homoscatter performs codeword translation on the Physical Layer Header (PHR) of the incoming ZigBee packets. This allows the tag to embed more information without requiring a complex or power-hungry modulation scheme on the payload itself.
  • FPGA-based Prototype: The system was prototyped using an FPGA, demonstrating the feasibility of implementing these techniques on hardware.

Datasets

Not discussed in the paper. The evaluation relies on experimental measurements in a practical environment.

Key Insights and Ideas

  • Leveraging Existing ZigBee Hardware is Key: The paper demonstrates that it's possible to build an efficient backscatter system using readily available ZigBee components, avoiding the need for specialized hardware for the exciting source.
  • Continuous Phase Change is Crucial for Spectral Purity: Shifting from instantaneous to continuous phase changes in modulation dramatically reduces spectral leakage, making the system a better neighbor to other wireless devices.
  • Packet Header Manipulation Offers Significant Gains: Modifying the packet header, rather than just the payload, provides a clever way to boost communication efficiency and throughput without drastically increasing complexity.
  • Trade-offs Exist: While Homoscatter excels in spectral efficiency and bidirectional communication, its performance at very close ranges can be slightly less robust than systems that solely focus on payload modulation, highlighting the importance of adaptive strategies.

Key Results

  • Occupied Bandwidth: Homoscatter achieves an occupied bandwidth of 2.38 MHz, which is the same as commodity ZigBee devices and 3x smaller than Interscatter (8.41 MHz).
  • Spectrum Efficiency: Homoscatter offers a 3x improvement in spectrum efficiency over Interscatter.
  • Goodput: In Line-of-Sight (LOS) deployments, Homoscatter achieves a goodput of 13 kbps and an uplink distance of up to 15 meters. In Non-Line-of-Sight (NLOS) scenarios, it reaches 10.3 kbps.
  • Interference Reduction: Homoscatter significantly reduces interference to neighboring Bluetooth and ZigBee devices, with Bluetooth BER remaining below 1% up to 8-9 meters, compared to Interscatter's BER reaching 20% at 6 meters.
  • Channel Capacity Utilization: Homoscatter utilizes over 74% of the excitation resources.

Limitations and Future Work

  • Close-Range Performance: The paper notes that at very close ranges, Homoscatter's performance can be slightly less robust than systems that solely modulate the payload, suggesting that adaptive modulation strategies (e.g., modulating both header and payload at close range) could further improve performance.
  • Detector Improvement: The authors observe that over 80% of bit errors occur in the translated packet header, indicating that improvements in the detector's ability to decode these headers could enhance overall reliability.
  • Future Work: The paper suggests exploring heterogeneous communication at further distances and building upon the demonstrated efficiency and spectral cleanliness of Homoscatter for future ultra-low power IoT applications.

Summary updated

Abstract

Recent advances in backscatter open a promising direction for ultra-low power communication. However, the state-of-art ZigBee backscatter system, Interscatter, has several drawbacks to deploy. Its backscatter tag and exciting source, Bluetooth, can hardly decode packets from other ZigBee nodes, which left Interscatter one-way communication. Besides, it adopts instantaneous phase change to modulate information, producing obvious sidelobes and interfering devices working on neighboring channels severely. To address the problems mentioned above, we introduce Homoscatter, a novel ZigBee backscatter system that adopts specific ZigBee devices to generate a single tone and leverages continuous phase change to modulate information, which eliminates spectral leakage. It also does codeword translation on the packet header of exciting packets, improving the utilization of ambient signal. The prototype of Homoscatter consists of a microchip radio, a backscatter tag, and a commodity receiver. The evaluations show that the occupied bandwidth of Homoscatter achieves 3x smaller than Interscatter. When the channel capacity is 17.5 kbps, the continuous phase change modulation achieves 13 kbps with the codeword translation on the excitation header. Based on the widely spread IoT devices, Homoscatter is a practical way to build an efficient connection between IoT devices.
BibTeX
@misc{xu2021homoscatter,
  author = {Zhaoyuan Xu and Wei Gong},
  title = {{Homoscatter: Towards efficient connectivity for ZigBee backscatter system}},
  year = {2021},
  eprint = {2111.02140},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2111.02140},
}

Loading related content...

Figure