Friction and wear mechanism of the projectile rotating band

Zoran Ristić, Slobodan Ilić, Aleksandar KariVojnotehnicki 2005 · DOI

Abstract

This paper describes a friction and wear model for projectile rotating bands, focusing on the heating and melting of material at the contact surface between the bore and the projectile. A hydrodynamic slider-bearing model is applied, utilizing the Reynolds equation for the resulting "fluid" (melting film). The fluid temperature is assumed to be constant and equal to the melting temperature at the contact surface. Based on heat transfer calculations from the film (using the Landau model) and film thickness results, the coefficient of melt friction and material wear are determined. The study illustrates the influence of various parameters on friction force and film thickness through specific material examples.

Introduction

In interior ballistics, the "rotating band" is a ring of relatively soft metal—typically copper or an alloy—encircling a projectile. Its primary function is to engage the barrel's rifling, imparting the spin necessary for flight stability. However, the conditions inside a gun barrel are extreme: pressures are immense, and sliding velocities can reach 700 m/s.

At these speeds, the friction generated is so intense that the surface of the rotating band reaches its melting point almost instantly. This creates a complex tribological environment where the physics shifts from solid-on-solid contact to hydrodynamic lubrication. This research addresses the need for a quantitative model to predict how different materials, such as copper, brass, and bronze, will wear and how much friction they will generate under these extreme thermal loads.

Methodology

The authors treat the interface between the projectile and the barrel as a hydrodynamic slider-bearing. In this regime, the "lubricant" is not oil, but the thin film of melted metal itself. The modeling approach incorporates several key components:

  • Reynolds Equation: Adapted to model the flow of the molten metal film.
  • Landau Model: Used to calculate heat transfer for a melting solid where the liquid phase is constantly removed (squeezed out) by the motion.
  • Numerical Implementation: Due to the non-linear relationship between heat transfer, film thickness, and friction, the authors developed a solver in MATLAB. For cases where heat transfer is balanced, the model solves a 5th-degree polynomial to find the equilibrium film thickness.
Figure 1: Algorithm of the software solution for calculating friction and wear parameters based on input data and material properties.

Key Results and Discussion

The "Melt Lubrication" Regime

A primary insight from the model is that at high velocities, the friction coefficient actually decreases as speed increases. While counterintuitive, this is explained by the fact that higher speeds generate a thicker film of liquid metal, which acts as a more effective lubricant. For copper, the model predicts the friction coefficient ($f$) drops significantly from approximately 0.08 at 100 m/s to just 0.01 at 700 m/s.

Figure 2: Diagram showing the change in friction coefficient versus sliding velocity for different materials: (1) Melted copper, (2) Brass, (3) Copper, (4) Al-bronze.

Material Performance and Wear

The study highlights that in this high-speed regime, a material's thermal properties—specifically its melting point and thermal conductivity—are more critical for wear resistance than its structural hardness.

  • Brass Advantage: The model identifies brass as a superior material for rotating bands among those tested, as its thermal characteristics provide the best resistance to melt-induced wear.
  • Wear vs. Friction: While friction decreases with velocity, the wear rate climbs sharply. Faster projectile movement causes more material to melt and be squeezed out of the contact zone.
  • Film Thickness: The calculated melt film is extremely thin, ranging from approximately 2 to 39 micrometers depending on the velocity and material.

Conclusion

The developed thermal/hydrodynamic model effectively captures the dominant physics of the projectile-barrel interface at high speeds. It confirms that the "melt-shield" governs the friction and temperature at the contact surface. However, the authors note that real-world gun barrels are rifled, and a significant portion of wear comes from "engraving"—the mechanical cutting of the band by the steel rifling. Future work aims to integrate this mechanical mechanism with the current thermal model to provide a complete physical picture of projectile wear.

Summary updated

Abstract

Friction and wear model of rotating band, due to, heating and melting material between the contact surface of a bore and projectile is described in this paper. The hydrodynamic slider-bearing model of the metal rotating band is applied and the Reynold's equation for the "fluid" (melting film) has been used in this work. The fluid temperature was assumed to be constant and equal to the melting temperature on the contact surface. Based on the total heat transfer from the film, which is made, between the melting on the non-melting surface (Landan model) and certain results of the film thickness, the coefficient of melt friction and the material wear were achieve. The size wears of the projectile rotating band and influence of certain parameters on the friction force and the film thickness are given in this paper. The achieved results have been illustrated by chosen example. .
BibTeX
@inproceedings{ristic2005friction,
  author = {Zoran Ristić and Slobodan Ilić and Aleksandar Kari},
  title = {{Friction and wear mechanism of the projectile rotating band}},
  booktitle = {Vojnotehnicki},
  year = {2005},
  doi = {10.5937/vojtehg0505397r},
}
Figure