Abstract
Solid solution of MgSO4 and Al2(SO4)3 was prepared from mixed aqueous solutions by rapid dry using micro-wave heating. The Mg2+ ion is soluble into the anhydrous aluminum sulfate crystal lattice over a wide range up to near the equimolar composition of MgSO4 and Al2(SO4)3. The anhydrous aluminum sulfate solid solution, at first, thermally decompose into the mixture of η-Al2O3 and MgSO4. The crystalline spinel phase appears at the second step of the thermal decomposition. The lattice parameters of the spinel changes linearly with the Mg content ranging from 0.5 to 0.8 at the fraction of MgAl2O4/(MgAl2O4+Al2O3). The produced nonstoichiometric spinel solid solutions must be metastable because the stable region of the composition of the spinel solid solutions is very narrow at the heating temperature employed to the thermal decomposition.
Introduction
Magnesium aluminate spinel ($MgAl_2O_4$) is a high-performance ceramic material valued for its high melting point ($2135^\circ C$) and exceptional chemical resistance. Conventional synthesis typically relies on solid-state reactions between magnesium and aluminum oxides at extreme temperatures. However, this approach often suffers from slow reaction kinetics and microscopic chemical inhomogeneities. This study investigates an alternative sulfate-based precursor route, utilizing microwave processing to achieve a highly uniform solid solution that subsequently decomposes into a spinel phase.
Methods
Aqueous solutions of aluminum sulfate and magnesium sulfate were mixed in various molar ratios. To maintain ionic homogeneity during dehydration, the solutions were subjected to high-power microwave heating (1.4 kW), which rapidly "froze" the mixed state into a solid precursor. The resulting powders were dehydrated at $400^\circ C$ and subsequently calcined at $900^\circ C$ for four hours to trigger thermal decomposition. Characterization was performed using X-ray Diffraction (XRD) to determine lattice constants and Thermogravimetry (TG) to analyze the weight loss behavior during thermal decomposition.
Results and Discussion
Formation of Anhydrous Sulfate Solid Solution
A key discovery was the extensive solubility of $Mg^{2+}$ ions within the anhydrous aluminum sulfate crystal lattice. Analysis of the XRD data revealed that a single-phase solid solution forms across a wide range, up to nearly a 1:1 molar ratio of $MgSO_4$ to $Al_2(SO_4)_3$.
As shown in Figure 4, the lattice constants ($a_0$ and $c_0$) and the unit cell volume of the anhydrous sulfate phase exhibit a linear relationship with the magnesium content. This linear expansion confirms the successful incorporation of magnesium into the aluminum sulfate lattice, creating a truly homogeneous precursor.
Thermal Decomposition Mechanism
The transition from sulfate to oxide occurs via a distinct two-stage process. Thermogravimetric analysis (TG) was employed to track this decomposition as a function of temperature.
As illustrated in Figure 2, the first stage of weight loss corresponds to the decomposition of the aluminum sulfate component, resulting in the formation of $\eta-Al_2O_3$ (eta-alumina) and residual $MgSO_4$. The second stage, occurring at higher temperatures (approx. $800-900^\circ C$), involves the decomposition of $MgSO_4$ and its simultaneous reaction with the alumina to form the crystalline spinel phase.
Spinel Formation and Metastability
The spinel phase produced at $900^\circ C$ is non-stoichiometric, containing an excess of alumina. While the lattice parameters of this spinel vary linearly with magnesium content, the phase is metastable. Heating the samples further to $1250^\circ C$ causes the metastable spinel to partition into stable $\alpha-Al_2O_3$ (corundum) and stoichiometric $MgAl_2O_4$. This indicates that the sulfate route allows for the synthesis of unique intermediate states that are inaccessible via standard equilibrium oxide mixing.
Conclusion
The use of microwave-assisted drying of sulfate solutions provides a robust pathway for synthesizing highly homogeneous magnesium-aluminum precursors. The resulting metastable, non-stoichiometric spinels offer a unique opportunity to control ceramic composition at lower temperatures than traditional methods. Future work should address the physical morphology of these powders to optimize their performance in industrial sintering processes.
Summary updated