Flexural Vibrations of Rods with Viscoelastic Coating Subjected to Axial Force

Hideo Saitô, Kiichi Sato, Takayuki AraiBulletin 1973 · DOI

Abstract

This study develops the governing equation for the flexural free vibration of a viscoelastic bar with a viscoelastic coating subjected to a static axial force, utilizing Bernoulli-Euler beam theory. A general solution is derived for a simply supported coated bar where both core and coating materials are represented by a four-element linear viscoelastic model. Numerical analysis of a bar with an aluminum core and Acrylite resin coating demonstrates that damping increases monotonically with the coating-to-core sectional area ratio. Crucially, the application of an axial compressive force significantly enhances damping, particularly at lower vibration frequencies.

Introduction

In structural engineering, controlling vibrations is vital for maintaining performance and structural integrity. A common mitigation strategy involves applying viscoelastic coatings to structural members to dissipate mechanical energy. However, structural components are frequently subjected to axial loads—tension or compression—that can alter their dynamic response.

While previous research has examined the damping properties of coatings in isolation, the interaction between axial stress and viscoelastic damping remains less understood. This paper investigates how axial forces influence the vibration and damping characteristics of coated rods, specifically focusing on whether these forces can be leveraged to enhance energy dissipation.

Methodology and Material Modeling

The research employs Bernoulli-Euler beam theory to derive the governing equations of motion for a composite rod. To accurately capture the time-dependent behavior of the materials, the authors utilize a four-element linear viscoelastic model (Figure 2). This versatile model can be reduced to simpler Maxwell, Voigt, or standard linear solid models by adjusting its parameters, allowing for a broad range of material simulations.

The four-element linear viscoelastic model used to characterize the core and coating materials.

The differential equations were solved for a simply supported bar to determine the complex circular frequency, where the imaginary component represents the damping capacity. Numerical simulations were conducted using material constants for an aluminum core (modeled as a standard linear solid) and an Acrylite resin coating (modeled as a Maxwell material). These simulations explored the relationship between the logarithmic decrement ($\delta$), slenderness ratio ($\mu$), coating thickness, and axial force.

Key Results and Insights

The analysis yielded several significant findings regarding the tunability of structural damping:

  • Compression as a Damping Multiplier: Axial compressive force acts as a significant multiplier for the damping effect. As the compressive force ($S$) approaches the buckling load ($S_b$), the logarithmic decrement increases dramatically.
  • Frequency and Slenderness Effects: The impact of axial force is highly dependent on the rod's geometry. It is most pronounced at lower frequencies, which correspond to higher slenderness ratios ($\mu$). For a rod with $\mu = 1500$, damping was found to be nearly double that of a rod with $\mu = 500$ under similar loading conditions.
  • Coating Volume Influence: Damping increases monotonically with the ratio of the coating's cross-sectional area ($A_2$) to the core's area ($A_1$). While more coating material improves energy dissipation, it also affects the overall natural frequency of the bar.
Logarithmic decrement $\delta$ as a function of slenderness ratio $\mu$ for various coating area ratios $A_2/A_1$ under a compressive force $S/S_b = 0.4$.

As illustrated in Figure 6, the combination of high slenderness and significant compressive load ($S/S_b = 0.4$) results in the highest damping values. This suggests that long, slender structural members are particularly well-suited for vibration suppression via viscoelastic coatings when under axial compression.

Conclusion and Limitations

The study provides a rigorous theoretical foundation for predicting the behavior of coated rods under axial stress. However, several limitations are noted:

  • Theoretical Nature: The results are purely numerical and theoretical; experimental verification with physical prototypes is necessary to validate the model's predictions.
  • Geometric Assumptions: The study focuses on circular cross-sections and small deflections. Effects such as shear deformation and rotatory inertia, which are significant in thicker beams or at very high frequencies, were not included.
  • Material Non-linearity: Real-world viscoelastic materials often exhibit temperature sensitivity and non-linear strain behavior that the four-element linear model may not fully capture.

Despite these constraints, the research highlights a promising avenue for structural control: the ability to "tune" damping characteristics by adjusting the axial loads carried by structural components.

Summary updated

Abstract

The governing equation of the flexural free vibration of a viscoelastic bar with a viscoelastic coating subjected to a static axial force is developed by utilizing the Bernoulli-Euler beam theory. The general solution is obtained for a simpy supported coated bar where both core and coating materials are described by a four element linear viscoelastic model. As a numerical example, the free vibration of a coated bar, composed of core and coating materials described by the standard linear solid and Max-well models, respectively, has been analysed. In the present example, the results show that the effect of damping increases monotonically with an increase in the ratio of the sectional area of coating to that of core and also the application of an axial compressive force to a viscoelastic coated bar yields high damping.
BibTeX
@article{saito1973flexural,
  author = {Hideo Saitô and Kiichi Sato and Takayuki Arai},
  title = {{Flexural Vibrations of Rods with Viscoelastic Coating Subjected to Axial Force}},
  journal = {Bulletin},
  year = {1973},
  doi = {10.1299/jsme1958.16.705},
}
Figure