Fabrication of Microcavity with Magneto- and Electro-Optical Film

Taichi Goto, Ryosuke Hashimoto, Ryosuke Isogai, Yuta Suzuki, Ryuhei Araki, Hiroyuki Takagi, Mitsuteru InoueJournal of the Magnetics Society of Japan 2012 · DOI

Introduction

Spatial Light Modulators (SLMs) are critical components for advanced optical technologies, including holographic storage and 3D displays. While liquid crystal-based SLMs are common, their response times are often insufficient for high-speed applications. Magneto-optical SLMs (MOSLMs) offer faster switching but typically rely on current-driven mechanisms that generate excessive heat. This research explores a voltage-driven alternative: a microcavity structure integrating both magneto-optical (MO) and electro-optical (EO) thin films within a magnetophotonic crystal (MPC) framework.

Device Architecture and Methods

The researchers designed a complex multi-layered microcavity using Ion Beam Sputtering (IBS). The structure consists of a MO garnet film and an EO PLZT film sandwiched between two dielectric Bragg mirrors (BMs).

Schematic of the microcavity structure showing the arrangement of Bragg mirrors, MO garnet, EO PLZT, and ITO electrodes.

The specific layers include:

  • Bragg Mirrors (BMs): Periodic stacks of $Ta_2O_5$ (89 nm) and $SiO_2$ (134 nm) designed to localize light.
  • Magneto-Optical (MO) Layer: A 360 nm bismuth-substituted iron garnet film ($(BiDyY)_3(FeAl)_5O_{12}$).
  • Electro-Optical (EO) Layer: A (Pb,La)(Zr,Ti)$O_3$ (PLZT) film.
  • Transparent Electrodes: Indium Tin Oxide (ITO) layers (85 nm) positioned to apply an electric field across the EO film.
  • Substrate: The entire stack is grown on a (GdCa)$_3$(GaMgZr)$_5O_{12}$ (SGGG) substrate with an anti-reflection coating on the backside.

Fabrication Challenges: The Buffer Layer Solution

A primary hurdle in fabricating this hybrid device was maintaining the integrity of the PLZT film during high-temperature crystallization. Standard deposition often led to pinholes or peeling. To resolve this, the team implemented a two-step deposition process. A thin 16 nm PLZT buffer layer was deposited first, followed by the main 176 nm layer. This approach suppressed irregular grain growth and reduced film stress, resulting in a dense, high-quality film capable of withstanding the 750°C Rapid Thermal Annealing (RTA) process.

Additionally, the researchers confirmed that the ITO electrodes deposited via IBS remained highly conductive even after exposure to 900°C, a necessary trait given the high processing temperatures required for the active MO and EO layers.

Experimental Results

The fabricated samples successfully demonstrated simultaneous magneto-optical and electro-optical functionality. X-ray diffraction confirmed the desired crystalline phases, and Sawyer-Tower measurements showed electrical polarization loops in the PLZT layer (approximately 10 μC/cm² at 6V).

Crucially, the microcavity effect was verified through Faraday rotation measurements. The structure exhibited enhanced Faraday rotation at specific localized mode wavelengths.

Faraday rotation loops measured at localized mode wavelengths of 750 nm and 880 nm.

As shown in the figure, clear hysteresis loops were observed at 750 nm and 880 nm, confirming that the microcavity successfully trapped light and enhanced the MO interaction within the garnet layer.

Conclusion and Future Outlook

This study demonstrates the feasibility of integrating MO and EO materials into a single, functional microcavity. While the observed Faraday rotation was lower than theoretical maximums—attributed to optical losses in the PLZT film and non-optimized mirror reflectivity—the successful simultaneous operation of both layers marks a significant milestone. Future work will focus on increasing the number of Bragg mirror layers and optimizing electrode thickness to minimize phase interference and maximize modulation efficiency for next-generation e-MOSLMs.

Summary updated

Abstract

We fabricated a microcavity -a magneto-optical (MO) film and an electro-optical (EO) film are sandwiched between two Bragg mirrors (BMs)- for development of magneto-optical spatial light modulators driven by electric field (e-MOSLMs). We used (Bi0.5Dy0.7Y1.8)3(Fe3.3Al1.7)5O12 as a MO film and (Pb91La9)1(Zr65Ti35)1O3 (PLZT) as an EO film. The samples showed enhanced Faraday rotation loops and electrical polarization loops, simultaneously. The X-ray diffraction patterns, MO and EO characteristics were measured. Experimental results showed that EO and MO films were successfully formed between BMs.
BibTeX
@article{goto2012fabrication,
  author = {Taichi Goto and Ryosuke Hashimoto and Ryosuke Isogai and Yuta Suzuki and Ryuhei Araki and Hiroyuki Takagi and Mitsuteru Inoue},
  title = {{Fabrication of Microcavity with Magneto- and Electro-Optical Film}},
  journal = {Journal of the Magnetics Society of Japan},
  year = {2012},
  doi = {10.3379/msjmag.1204r010},
}
Figure