TL;DR
This paper investigates how using waste vegetal fibers as fillers in 3D-printed PLA composites affects their mechanical properties, particularly how these properties change based on the printing orientation. The findings show that these biocomposites exhibit significant anisotropic behavior, meaning their strength and stiffness vary depending on the direction of printing, offering a promising avenue for sustainable and customizable material design.
What Problem Does This Paper Address?
The widespread adoption of 3D printing, especially fused filament fabrication (FFF), is currently limited by the inherent mechanical weaknesses of pristine polymer parts. While incorporating short fibers into polymer filaments is a known method to enhance mechanical properties, the use of sustainable, waste-derived natural fibers in 3D-printed composites is still an active area of research. Furthermore, the anisotropic nature of 3D-printed parts, where mechanical properties differ along different printing directions, is a critical factor for structural applications. This study aims to address these challenges by exploring the anisotropic mechanical behavior of 3D-printed biocomposites made from waste vegetal fibers, offering a more environmentally friendly and potentially tunable alternative to traditional synthetic fiber composites.
Methods
The researchers utilized a FFF 3D printer to fabricate samples from polylactic acid (PLA) and four types of waste vegetal fiber-filled PLA filaments: tomato, pruned orange tree, hemp, and weed. These filaments were characterized for their fiber content using thermogravimetric analysis (TGA) and their morphology was examined using scanning electron microscopy (SEM). The core of the study involved systematically printing samples with varying print orientations (0° to 90°) and then subjecting them to tensile testing using a universal mechanical testing machine. The anisotropic mechanical behaviors were assessed by comparing the tensile strength and elongation at break of samples printed in different orientations. Fracture surfaces were analyzed using optical microscopy and FE-SEM to understand the failure mechanisms and their relationship with print orientation.
Datasets
Not discussed in the paper. The study focuses on experimental fabrication and testing of custom composite materials.
Key Insights and Ideas
- Waste Valorization for Performance: The study demonstrates that agricultural waste, such as tomato and orange tree residues, can be effectively utilized as fillers in 3D-printable biocomposites, contributing to both sustainability and enhanced material properties.
- Anisotropy is Key: The research highlights that the mechanical properties of these vegetal fiber-filled composites are highly dependent on the print orientation. This anisotropy is not just present but can be significant, offering opportunities to tailor part performance by controlling the printing direction.
- Fiber Type Matters for Anisotropy: Different vegetal fibers (tomato, pruned orange, hemp, weed) lead to varying degrees of anisotropic behavior, suggesting that careful selection of fiber type can further fine-tune the material's directional properties.
- Pores as a Trade-off: While the addition of vegetal fibers improves anisotropic mechanical properties compared to pure PLA, the presence of pores introduced during filament manufacturing can lead to a lower overall peak load in some cases. This points to a need for optimizing filament production to mitigate pore formation.
- Failure Mechanisms Reveal Anisotropy: The observed fracture morphologies, such as shear failure and interlayer delamination, directly correlate with the print orientation and provide visual evidence for the anisotropic mechanical behavior.
Key Results
- Waste vegetal fiber-filled polymer biocomposites (WVFFPBs) exhibited significantly higher anisotropic mechanical properties in the 0° and 90° directions compared to pristine PLA samples.
- For weed vegetal fiber-filled composites, the elongation at break and peak load differed by 45.8% and 69.4%, respectively, between the 0° and 90° print orientations.
- As the printing angle increased from 0° to 90°, the tensile mechanical properties of the WVFFPBs generally showed a decreasing trend.
- The tensile strength of pruned fiber-filled composites printed at 45° and 30° orientations showed a difference of 37.8% (8.77 MPa vs. 14.09 MPa).
- Fracture analysis revealed that print orientation controlled damage, with different angles leading to distinct fracture morphologies, such as serrated fractures perpendicular to the print direction or shear failure along the print direction.
Limitations and Future Work
The authors acknowledge that the presence of pores in the filaments, attributed to the manufacturing process, can reduce the peak load of the WVFFPBs compared to pure PLA. While the study successfully demonstrated anisotropic mechanical behaviors, further optimization of filament processing to minimize pore formation would be beneficial.
The authors suggest that future work should investigate the natural degradation performance of these 3D-printed short vegetal fiber-filled biocomposites, considering the influence of printing parameters and the environment. This would be a meaningful step towards developing truly sustainable and biodegradable 3D-printed materials.
Summary updated