Experimental Study of Lean Premixed CH4/N2/O2 Flames under High-Frequency Alternating-Current Electric Fields

Hao Duan, Xiaomin Wu, Cong Zhang, Yuchen Cui, Juncai Hou, Chao Li, Zhongquan GaoEnergy 2015 · DOI

TL;DR

This study experimentally investigates the impact of high-frequency alternating current (AC) electric fields on lean methane-oxygen-nitrogen (CH4/N2/O2) flames. The researchers found that increasing the frequency and voltage of the AC electric field significantly enhances flame propagation speed and combustion efficiency, primarily through an "electrical-chemical effect." This work offers valuable insights for developing electric-field-assisted combustion technologies.

What Problem Does This Paper Address?

Lean combustion is a crucial strategy for reducing energy consumption and emissions in engines. However, lean mixtures inherently burn slower, limiting their practical application. While electric fields have been explored to enhance combustion, the specific effects of high-frequency AC electric fields on lean flames, particularly the underlying mechanisms, remain less understood. This paper aims to fill this knowledge gap by systematically studying how varying the frequency and voltage of high-frequency AC electric fields influences the combustion characteristics of lean CH4/N2/O2 flames.

Methods

The researchers employed a constant-volume combustion bomb setup to study the combustion of lean CH4/N2/O2 mixtures. Key experimental components included a high-voltage AC power supply, a high-speed camera for flame visualization, and a pressure transducer to monitor combustion pressure. The experiments involved systematically varying the AC electric field frequency (5–30 kHz) and applied voltage (0–5 kV) while keeping the excess air ratio (λ = 1.2, 1.4, 1.6) constant. Flame propagation speed was determined by analyzing the flame radius over time from the high-speed camera footage. Combustion characteristics like peak pressure and its timing were also recorded. The study also included a 3D simulation of the electric field distribution within the combustion chamber using ANSOFT Maxwell software to understand the field's behavior.

Datasets

Not discussed in the paper. The study relies on experimental data generated from controlled combustion experiments within the described setup.

Key Insights and Ideas

  • Dominance of the Electrical-Chemical Effect: The paper argues that for high-frequency AC electric fields, the "ionic wind effect" (bulk flow of gas due to ion migration) is negligible. Instead, the primary mechanism for flame enhancement is the "electrical-chemical effect," where charged particles absorb electromagnetic energy and become excited, directly influencing chemical reactions in the pre-flame zone.
  • Frequency Transition Point: Flame propagation speed increases with frequency up to a certain point, around 25 kHz, after which it stabilizes. This suggests an optimal frequency range for maximizing the electrical-chemical effect.
  • Exponential Voltage Dependence: The mean flame propagation speed increases nearly exponentially with applied voltage. This indicates that higher electric field intensities are significantly more effective at promoting combustion.
  • Leaner Mixtures Benefit More: The enhancement in flame propagation speed and reduction in combustion duration are more pronounced for leaner mixtures (higher excess air ratios), suggesting that electric fields can help overcome the inherent slowness of very lean combustion.
  • Flame Shape Distortion: High-frequency AC electric fields cause flames to stretch in the horizontal direction, leading to elliptical shapes, while the vertical dimension remains relatively unchanged.

Key Results

  • Flame Propagation Speed:
    • Mean flame propagation speed increases with frequency, stabilizing around 25 kHz.
  • Mean flame propagation speed increases exponentially with applied voltage. For example, at 15 kHz and λ=1.2, the speed increased from 1.14 m/s (0 kV) to 1.42 m/s (5 kV).
  • Relative increase in flame propagation speed (AS,) was significant, reaching up to 97.89% at 30 kHz and 5 kV for λ=1.6 compared to the no-field case.
  • Combustion Characteristics:
    • Peak combustion pressure (Pmax) showed a minimal increase (e.g., up to 4.64% for λ=1.2 at various frequencies).
  • The timing of peak pressure (tp) decreased significantly with both increasing frequency and voltage. For λ=1.6, tp decreased by up to 28.47% with increasing frequency and by up to 25.01% with increasing voltage.
  • Initial and main combustion durations (tid and tmd) were also shortened, with similar trends to peak pressure timing. For λ=1.6, tmd decreased by up to 23.28% with increasing frequency and by up to 21.89% with increasing voltage.

Limitations and Future Work

  • Mechanism Nuances: While the electrical-chemical effect is identified as dominant, the paper acknowledges that the exact mechanism is not fully concluded. Further research could delve deeper into the specific chemical pathways influenced by the electric field.
  • Transition Frequency: The paper identifies a transition frequency around 25 kHz but suggests that further investigation into the precise value and its dependence on other parameters could be beneficial.
  • Experimental Scope: The study focused on CH4/N2/O2 flames. Future work could explore the effects on other fuel types or different mixture compositions.
  • Practical Application: While the results are promising for electric-field-assisted combustion, translating these findings to real-world applications like internal combustion engines would require further engineering and validation. The authors suggest this work has positive implications for the further study of electric-field-assisted combustion theory.

Summary updated

Abstract

In order to study the effect of the frequency and the intensity of high-frequency alternating-current (AC) electric fields on lean combustion, the effects of high-frequency (5–30 kHz; 5 kV) and high-voltage (0–5 kV; 15 kHz) AC electric fields on lean (excess air ratio 1.2/1.4/1.6) premixed CH4/N2/O2 flames are evaluated experimentally in the paper in detail. Results show that the mean flame propagation speed increases with the electric field frequency at first. However, the transition frequency, after which the mean flame propagation speed reaches to the maximum and then tends to be stabilized, is shown to be around 25 kHz. The combustion peak pressure increases minimally at various frequencies, but the timing of it decreases apparently; additionally, the effect of frequency on the combustion pressure change is very close to that on the mean flame propagation speed. The initial duration and main duration also have a similar tendency with the increase of the frequency. Besides, with the increase of the applied voltage, the mean flame propagation speed increases nearly exponentially. Meanwhile, the combustion peak pressure increases, and the timing of it decreases. Similarly, the effect of applied voltage on the combustion pressure change is also close to that on the mean flame propagation speed, and the initial duration and main duration also declines with the increase of the applied voltage. The result shows that the combustion of lean mixtures can be enhanced effectively by high-frequency (5–30 kHz) and high-voltage (1–5 kV) AC electric fields, which has a positive meaning in the further study of the electric-field-assisted combustion theory.
BibTeX
@inproceedings{duan2015experimental,
  author = {Hao Duan and Xiaomin Wu and Cong Zhang and Yuchen Cui and Juncai Hou and Chao Li and Zhongquan Gao},
  title = {{Experimental Study of Lean Premixed CH<sub>4</sub>/N<sub>2</sub>/O<sub>2</sub> Flames under High-Frequency Alternating-Current Electric Fields}},
  booktitle = {Energy},
  year = {2015},
  doi = {10.1021/acs.energyfuels.5b01420},
}

Loading related content...

Figure