Experimental Research on Shear Failure Monitoring of Composite Rocks Using Piezoelectric Active Sensing Approach

Yang Liu, Yicheng Ye, Qihu Wang, Weiqi WangSensors 2020 · DOI

TL;DR

This paper introduces a novel approach for monitoring shear failure in composite rocks, a critical challenge in underground engineering. By embedding piezoelectric smart aggregates (SAs) and analyzing stress wave propagation with wavelet packet analysis, the researchers developed a quantitative method to track damage progression and provide early warnings.

What Problem Does This Paper Address?

Underground space engineering often involves complex geological formations, particularly "composite rocks" where different rock masses meet. These interfaces are prone to shear failure due to differential deformation, posing significant safety risks. Existing monitoring methods struggle to accurately track the dynamic process of shear failure at these interfaces. This paper aims to fill this gap by developing a reliable and quantitative method for monitoring shear failure in composite rock structures.

Methods

The core of this research lies in the combination of two key techniques:

  • Piezoelectric Active Sensing: This method utilizes piezoelectric smart aggregates (SAs) embedded within the composite rock specimens. One SA acts as an actuator, emitting a swept sine wave signal. The other SA acts as a sensor, detecting the wave as it propagates through the rock interface. Changes in the received signal's amplitude, peak value, and energy are indicative of damage.
  • Wavelet Packet Analysis: To quantify the damage, the researchers employed wavelet packet analysis. This technique decomposes the received signal into various frequency bands, allowing for the calculation of the signal's energy within each band. By comparing the energy distribution before and after damage, a "shear failure damage index" is computed. This index quantifies the relative loss of transmitted signal energy, providing a measure of the rock's damage state.

The experimental setup involved fabricating composite rock specimens from cement, embedding two pairs of SAs symmetrically across the interface, and subjecting them to direct shear tests.

Datasets

Not discussed in the paper. The study relies on experimental data generated from fabricated composite rock specimens under controlled laboratory conditions.

Key Insights and Ideas

  • Signal Attenuation as a Damage Indicator: The study clearly demonstrates that shear failure at the composite rock interface leads to a significant attenuation (decrease) in the amplitude, peak value, and energy of the stress waves transmitted between the SAs. This provides a direct, measurable indicator of damage.
  • Quantitative Damage Index: The wavelet packet analysis successfully translates the observed signal changes into a quantitative "shear failure damage index." This moves beyond qualitative observations to provide a numerical representation of the damage progression.
  • Abrupt Damage Index Increase: The damage index shows a gradual increase during the shearing process, followed by an abrupt jump as the specimen approaches and undergoes shear failure, reaching a value close to 1. This sharp increase serves as a crucial warning signal.
  • Feasibility and Reliability: The consistent results across multiple specimens, despite minor variations, highlight the feasibility and reliability of the piezoelectric active sensing and wavelet packet analysis approach for monitoring composite rock shear failure.

Key Results

  • Signal Amplitude Drop: Upon shear failure, the amplitude and peak values of the monitoring signals decreased significantly. For instance, in Composite specimen I, the signal amplitude after 22 minutes (failure) was significantly lower than at 20 minutes.
  • Damage Index Behavior: The shear failure damage index showed a gradual increase during the shearing process and then abruptly increased to near 1 upon failure. For Composite specimen I, the damage index reached approximately 0.9520 (SA3) and 0.9922 (SA4) at failure.
  • Failure Time Correlation: The observed signal changes and damage index increases closely correlated with the actual shear failure times of the composite specimens, which ranged from approximately 19.8 to 22 minutes.
  • High Sensitivity: The method demonstrated high sensitivity, with obvious drops in stress wave values upon damage, making it suitable for early warning systems.

Limitations and Future Work

  • Laboratory vs. Real-World Conditions: The authors acknowledge that actual engineering conditions are far more complex than laboratory settings. Further research is needed to apply and validate this method in real-world underground space engineering scenarios.
  • Modeling Interface Behavior: Future work will involve modeling the stress wave propagation across the interface in composite rocks using fractal contact theory. This will provide a deeper theoretical understanding of the phenomena observed.
  • Generalizability: While the study demonstrates success with cement-based composite rocks, further investigation into different types of composite rock formations would be beneficial.

Summary updated

Abstract

Underground space engineering structures are generally subject to extensive damages and significant deformation. Given that composite rocks are prone to shear failure, which cannot be accurately monitored, the piezoelectric active sensing method and wavelet packet analysis method were employed to conduct a shear failure monitoring test on composite rocks in this study. For the experiment, specimens were prepared for the simulation of the composite rocks using cement. Two pairs of piezoelectric smart aggregates (SAs) were embedded in the composite specimens. When the specimens were tested using the direct shear apparatus, an active sensing-based monitoring test was conducted using the embedded SAs. Moreover, a wavelet packet analysis was conducted to compute the energy of the monitoring signal; thus allowing for the determination of the shear damage index of the composite specimens and the quantitative characterization of the shear failure process. The results indicated that upon the shear failure of the composite specimens, the amplitudes and peak values of the monitoring signals decreased significantly, and the shear failure and damage indices of the composite specimens increased abruptly and approached a value of 1. The feasibility and reliability of the piezoelectric active sensing method, with respect to the monitoring of the shear failure of composite rocks, was therefore experimentally demonstrated in this study.
BibTeX
@inproceedings{liu2020experimental,
  author = {Yang Liu and Yicheng Ye and Qihu Wang and Weiqi Wang},
  title = {{Experimental Research on Shear Failure Monitoring of Composite Rocks Using Piezoelectric Active Sensing Approach}},
  booktitle = {Sensors},
  year = {2020},
  doi = {10.3390/s20051376},
}
Figure