Experimental Investigation of the Performance of a Novel Ejector–Diffuser System with Different Supersonic Nozzle Arrays

Dachuan Xu, Yunsong Gu, Wei Li, Jingxiang ChenFluids 2024 · DOI

TL;DR

This paper introduces a novel rectangular supersonic-supersonic ejector-diffuser system designed for efficient low-pressure gas suction. By experimentally investigating the impact of different supersonic nozzle plate configurations, the researchers demonstrate how to optimize pressure control and avoid aerodynamic choking, offering a more practical design for wind tunnel applications.

What Problem Does This Paper Address?

Supersonic-supersonic ejectors are crucial components in various high-tech applications, from aerospace to cooling systems, for their ability to draw low-pressure fluids into high-pressure environments. However, designing these systems is challenging due to complex supersonic flow interactions and the risk of aerodynamic choking, which can severely degrade performance. Traditional circular ejectors are also not always ideal for ground-based testing facilities. This paper addresses the need for a more predictable and controllable supersonic ejector-diffuser system, specifically one with a rectangular cross-section suitable for wind tunnel experiments, and explores how to mitigate choking and enhance pressure control through novel nozzle designs.

Methods

The study employs a multi-faceted approach:

  • 1D Design Theory: A one-dimensional analysis was used to initially predict the ejector-diffuser's geometrical structure, particularly for the rectangular mixing section, based on desired operating conditions.
  • Novel Nozzle Plate Design: The core innovation lies in the design and implementation of different supersonic nozzle plates. These plates, varying in number and length, were strategically placed within the ejector to influence the supersonic flow and potentially delay or prevent aerodynamic choking.
  • Experimental Investigation: A straight-flow wind tunnel was used to conduct experiments. The system's pressure control performance was evaluated under various operating conditions, focusing on the effects of different nozzle plate configurations and backpressures. Static wall pressure measurements were taken at multiple points along the diffuser.

Datasets

Not discussed in the paper. The study relies on experimental data generated from the designed ejector-diffuser system under controlled laboratory conditions.

Key Insights and Ideas

  • Nozzle Plates are Key to Control: The type, number, and placement of supersonic nozzle plates significantly impact the onset of aerodynamic choking and the overall pressure-boosting performance. This offers a tunable mechanism for controlling the ejector's behavior.
  • Rectangular Design for Practicality: The rectangular cross-section of the ejector-diffuser is highlighted as being more convenient for ground test facilities like wind tunnels, offering a more uniform flow field and reduced boundary layer effects compared to circular designs.
  • Balancing Stability and Entrainment: Long nozzle plates excel at maintaining stable pressure in the test section, while shorter plates offer better pressure matching and higher entrainment ratios, especially under high backpressure conditions. This suggests a trade-off that can be managed through nozzle design.
  • Choking is a Critical Limit: The study emphasizes that aerodynamic choking is a critical phenomenon that must be understood and avoided for optimal performance. The inlet pressure of the ejecting stream is a key factor in its occurrence.

Key Results

  • Pressure Boosting Achieved: The designed ejector-diffuser system demonstrated the ability to boost low-pressure gas to higher pressure states. With three long nozzle plates, the outlet pressure could be boosted to approximately 4.5 times the backpressure ($P_D$).
  • Stable Vacuum Maintained: Systems with short nozzle plates showed a better capability to stabilize pressure and maintain a vacuum environment, with outlet pressures reaching up to 4.1 to 5.2 $P_D$.
  • Nozzle Plate Impact Quantified: Experiments showed that the static wall pressure distribution and the supersonic flow conditions in the diffuser were significantly influenced by the nozzle plate configuration. For instance, long nozzle plates maintained stable pressure when backpressure was below ~3.5-3.6 $P_D$, while short plates could handle higher backpressures (up to 4.1 $P_D$) with less disturbance.
  • COIL Laser Enhancement: The ejector-diffuser system was shown to improve the output power of a COIL laser by approximately 14.1% by creating a lower pressure environment in the test section.

Limitations and Future Work

  • 1D Analysis Simplification: While the 1D analysis provides a useful starting point for design, it simplifies complex supersonic flow phenomena. The paper acknowledges that more detailed CFD or experimental validation is crucial for optimizing geometry.
  • Off-Design Conditions: The paper mentions the importance of clarifying and avoiding off-design operating conditions, particularly those leading to aerodynamic choking. Further research could focus on defining the precise boundaries of stable operation for various configurations.
  • Nozzle Plate Optimization: While different nozzle plate types were tested, further optimization of their precise dimensions, angles, and placement could potentially yield even better performance across a wider range of conditions.
  • Boundary Layer Control: The paper briefly touches on how nozzle plate placement can affect boundary layers. Future work could explore more advanced boundary layer control strategies using these nozzle arrays.

Summary updated

Abstract

The supersonic–supersonic ejector–diffuser system is employed to suck supersonic low-pressure and low-temperature flow into a high-pressure environment. A new design of a supersonic–supersonic ejector–diffuser was introduced to verify pressure control performance under different operating conditions and vacuum background pressure. A 1D analysis was used to predict the geometrical structure of an ejector–diffuser with a rectangular section based on the given operating conditions. Different numbers and types of nozzle plates were designed and installed on the ejector to study the realizability of avoiding or postponing the aerodynamic choking phenomenon in the mixing section. The effects of different geometrical parameters on the operating performance of the ejector–diffuser system were discussed in detail. Experimental investigation of the effects of different types of nozzle plates and the back pressures on the pressure control performance of the designed ejector–diffuser system were performed in a straight-flow wind tunnel. The results showed that the position, type and number of the nozzle plates have a significant impact on the beginning of the formation of aerodynamic choking. The geometry of the ejector and the operating conditions, especially the backpressure and inlet pressure of the ejecting stream, determined the entrainment ratio of the two supersonic streams. The experimental results showed that long nozzle-plate had a better performance in terms of maintaining pressure stability in the test section, while short a nozzle-plate had a better pressure matching performance and could maintain a higher entrainment ratio under high backpressure conditions.
BibTeX
@inproceedings{xu2024experimental,
  author = {Dachuan Xu and Yunsong Gu and Wei Li and Jingxiang Chen},
  title = {{Experimental Investigation of the Performance of a Novel Ejector–Diffuser System with Different Supersonic Nozzle Arrays}},
  booktitle = {Fluids},
  year = {2024},
  doi = {10.3390/fluids9070155},
}

Loading related content...

Figure