TL;DR
This paper investigates how to improve the bonding strength and fracture toughness of steel-CFRP hybrid composites, crucial for aerospace and automotive applications. By combining grit blasting surface treatment on steel with an adhesive interlayer, researchers significantly enhanced both Mode I and Mode II interfacial fracture toughness, demonstrating a synergistic effect that leads to more robust hybrid materials.
What Problem Does This Paper Address?
Fiber-metal laminates (FMLs), and specifically steel-CFRP (Carbon Fiber Reinforced Polymer) hybrid composites, offer a compelling combination of high specific strength, fatigue resistance, and impact tolerance, making them attractive for lightweight structural applications in aerospace and automotive industries. However, a major challenge in their manufacturing is achieving strong and durable bonding between the dissimilar materials (steel and CFRP). This weak interface can lead to delamination and premature failure, significantly degrading the overall structural integrity. Existing research has explored surface treatments and adhesives, but a comprehensive understanding of how these factors influence both Mode I (opening) and Mode II (shearing) interfacial fracture toughness, especially in co-cured steel-CFRP systems, remains an area needing further investigation. This paper aims to fill this gap by systematically evaluating the impact of different surface preparation methods for steel and the inclusion of an adhesive layer on the interfacial fracture toughness of co-cured steel-CFRP composites.
Methods
The researchers employed a combination of experimental testing and numerical simulations to assess the interfacial fracture toughness.
Experimental Methods: * Material Preparation: Four types of steel-CFRP hybrid composites were fabricated using different manufacturing processes: * Surface Treatments: Steel substrates were prepared using either abrasion (80 grit sandpaper) or grit blasting (60 mesh alundum). * Adhesive Inclusion: Some composites were co-cured directly, while others had an epoxy adhesive layer introduced at the steel/CFRP interface. * Mode I Fracture Toughness Testing: Double Cantilever Beam (DCB) tests were conducted according to ASTM D5528 to measure the Mode I interfacial fracture toughness ($G_{IC}$). Load and displacement data were recorded, and crack lengths were meticulously tracked. The Modified Beam Theory (MBT) was used for calculations. * Mode II Fracture Toughness Testing: End Notched Flexure (ENF) tests were performed following ASTM D7905 to evaluate the Mode II interfacial fracture toughness ($G_{IIC}$). Similar to DCB tests, load-displacement data and crack lengths were recorded, and the Compliance Calibration Method (CCM) was applied. * Surface Morphology Analysis: A laser confocal scanning microscope was used to examine the detached surfaces after fracture tests to understand the failure mechanisms.
Numerical Methods: * Finite Element Analysis (FEA): Two-dimensional FEA models of the hybrid composites were developed using ABAQUS/Explicit. These models incorporated cohesive elements to represent the steel/CFRP interface, allowing for the simulation of crack initiation and propagation. * Material Modeling: The models used orthotropic material properties for the CFRP laminate and cohesive element models with a traction-separation response to define the interface behavior. * Parameter Calibration: Interfacial tensile strengths ($N_I$) were determined by matching the numerical load-displacement curves from DCB tests to the experimental data. Interfacial shear strengths ($N_{II}$) were taken from previous experimental work.
Datasets
Not discussed in the paper. The study relies on experimental data generated from the fabricated composite specimens and material properties obtained from literature or manufacturer specifications.
Key Insights and Ideas
- Synergistic Improvement: The most significant finding is the synergistic effect of combining grit blasting surface treatment on steel with an adhesive interlayer. This combination yielded the highest Mode I and Mode II interfacial fracture toughness values, suggesting that these two approaches are not merely additive but work together to enhance bonding.
- Grit Blasting's Effectiveness: Grit blasting, compared to simple abrasion, creates a significantly rougher steel surface. This increased surface area and mechanical interlocking are crucial for improving both Mode I and Mode II fracture toughness.
- Adhesive Layer's Role: The introduction of an adhesive layer effectively bridges the dissimilar materials, providing a more compliant and robust interface that can absorb more energy during crack propagation.
- Mode-Dependent Failure Mechanisms: The failure modes observed under Mode I and Mode II loading conditions were distinctly different. Under Mode I, failure often involved fiber/epoxy interfacial failure of the CFRP, indicating that the steel/CFRP interface became stronger than the CFRP itself. Under Mode II, adhesive failure between steel and the adhesive layer was more prevalent, suggesting that the interface's shear strength is a critical factor.
- FEA for Parameter Estimation: The FEA approach proved valuable for estimating interfacial tensile strength, which is difficult to measure directly experimentally. The good agreement between numerical and experimental results validates the FEA models and the derived material properties.
Key Results
- Mode I Fracture Toughness ($G_{IC}$):
- Grit blasting treatment alone increased $G_{IC}$ compared to abrasion.
- Adding an adhesive layer significantly boosted $G_{IC}$ for both abrasion and grit blasting treatments.
- The combination of grit blasting and adhesive (HY-GBAD) achieved the highest $G_{IC}$, approximately 1.161 kJ/m².
- Mode II Fracture Toughness ($G_{IIC}$):
- Similar trends were observed for $G_{IIC}$, with grit blasting and adhesive inclusion leading to substantial improvements.
- The HY-GBAD specimen also exhibited the highest $G_{IIC}$, around 1.733 kJ/m².
- Interfacial Tensile Strength ($N_I$):
- Estimated interfacial tensile strengths increased significantly with improved surface treatments and adhesive inclusion.
- The HY-GBAD specimen showed the highest estimated $N_I$ of 20 MPa.
- Failure Modes:
- Mode I: HY-AB showed primarily steel/CFRP interface failure. HY-GB exhibited mixed failure. HY-ABAD showed adhesive cohesive failure. HY-GBAD showed fiber/epoxy interfacial failure, indicating the interface was stronger than the CFRP.
- Mode II: All specimens primarily exhibited adhesive failure between steel and the adhesive, with epoxy resin observed on grit-blasted surfaces.
Limitations and Future Work
- Mode I/II Mixing in DCB: The authors acknowledge that the DCB test, while primarily for Mode I, can involve some degree of Mode II loading due to the specimen geometry and crack propagation. This can lead to a mixed-mode fracture scenario. They suggest that for pure Mode I loading, the flexural rigidity of the CFRP should ideally match that of the steel.
- Interfacial Shear Strength ($N_{II}$) Source: The interfacial shear strengths used in the ENF FEA simulations were taken from previous studies. While this is common practice, direct experimental validation within this study would strengthen the findings.
- Future Work: The paper implicitly suggests that further optimization of surface treatment parameters (e.g., grit size, pressure) and adhesive formulations could lead to even greater improvements. Investigating the long-term durability and environmental resistance of these enhanced interfaces would also be valuable. Exploring the application of these findings to more complex structural designs and different metal-CFRP combinations could also be a logical next step.
Summary updated