TL;DR
This paper investigates the impact of web damage on the vertical bearing capacity of U-shaped girders, common in urban railways. Through full-scale testing and advanced numerical simulations, the study reveals that web damage significantly reduces bearing capacity, particularly when it occurs in the mid-span region, and highlights the vulnerability of U-shaped girder webs to lateral forces.
What Problem Does This Paper Address?
U-shaped girders are increasingly used in urban railway transit due to their aesthetic appeal and functional advantages, such as noise isolation. However, their thin-walled web, crucial for flexural performance, is susceptible to damage from accidental events like train derailments. While existing research covers general bridge design and train-impact analysis, there's a specific need to understand how web damage in U-shaped girders affects their ultimate vertical load-carrying capacity. This gap poses a risk to the safety and operational integrity of urban railway infrastructure.
Methods
The study employed a two-pronged approach:
- Full-Scale Model Test: A full-scale U-shaped girder was subjected to vertical loading to observe crack evolution, failure mechanisms, and ultimate bearing capacity. This provided crucial experimental data.
- Numerical Simulation: A refined finite element (FE) model was developed using LS-DYNA, a software known for its explicit integration algorithm suitable for highly nonlinear problems like structural failure. The model incorporated:
- Concrete Modeling: The continuous surface cap model (MAT_159) was used to capture confinement effects and softening behavior.
- Prestressed Tendon and Reinforcement Modeling: Material models and techniques were employed to simulate prestressing forces and reinforcement behavior, including the use of equivalent temperature-induced shrinkage for prestressed tendons.
- Boundary Conditions and Load Modeling: Realistic simply supported boundary conditions were simulated using various bearing types. The loading process was divided into steps, including dynamic relaxation for dead loads and prestress, followed by lateral and then vertical loading.
- Web Damage Simulation: To simulate accidental train collision, a quasi-static displacement-based lateral load was applied to the flange, inducing damage to the web. This approach was chosen for its efficiency in simulating the complex impact process.
The FE model was calibrated against the experimental results, particularly focusing on load-deflection curves and considering the effect of prestress loss.
Datasets
The study utilized data from a full-scale U-shaped girder model test conducted by the authors. This experimental data served as the primary dataset for validating the numerical model. No other external datasets were explicitly mentioned for training or evaluation.
Key Insights and Ideas
- Flexural Failure Dominance: Under vertical loads, U-shaped girders primarily fail in a flexural manner, with tension fracture in the tensile zone and yielding of reinforcement in the bottom slab, followed by concrete crushing in the compressive zone.
- Web Vulnerability: The thin-walled web, while crucial for flexural performance, is highly vulnerable to lateral impact, leading to significant damage and reduced lateral resistance.
- Mid-Span Damage is Critical: Damage to the web in the mid-span region has a more substantial negative impact on the vertical bearing capacity compared to damage at the beam ends.
- Two-Sided Damage is Catastrophic: Damage to both sides of the web leads to the most severe degradation of bearing capacity, effectively reducing the U-section to a bottom slab section.
- Damage Range vs. Region: The length (range) of the web damage has a less significant impact on the ultimate bearing capacity compared to the location (region) of the damage.
- Prestress Loss is Crucial: Accurately accounting for prestress loss is essential for obtaining realistic stiffness predictions in numerical models.
Key Results
- The full-scale test showed that the U-shaped girder exhibited linear deformation up to approximately 1.5 times the design load, with significant nonlinear behavior developing thereafter, reaching complete failure at 2.8 times the design load.
- The numerical model, after calibration with a 37% prestress loss, accurately predicted the load-deflection behavior observed in the full-scale test.
- Simulations of web damage revealed that:
- Damage at the beam end resulted in a 30.7% reduction in ultimate bearing capacity ($P_u$).
- Damage at the middle span or 1/4 span led to a 42.0%–43.2% reduction in $P_u$.
- Damage to both sides of the web caused a significant 62.5% decrease in $P_u$.
- Increasing the damaged length from 2m to 8m resulted in a reduction of $P_u$ from 40.9% to 47.7%, indicating a less pronounced effect than the damage region.
- The numerical simulations confirmed that the U-shaped girder is more likely to experience material strength failure rather than overturning under lateral load.
Limitations and Future Work
- Accidental Collision Complexity: The study acknowledges that simulating the full dynamic process of a derailed train-girder collision is complex and influenced by numerous factors. The quasi-static lateral loading approach, while efficient, is a simplification.
- Limited Damage Scenarios: While various damage regions were investigated, the study focused on specific types and locations of web damage. Future work could explore more complex damage patterns, including combined damage to the web and flanges.
- Long-Term Effects: The research primarily focuses on the immediate impact of damage. Investigating the long-term performance and durability of damaged U-shaped girders under service loads would be valuable.
- Design Recommendations: The authors recommend that the lateral resistance of the web should be carefully considered in the design of U-shaped girders to enhance operational safety. Future research could translate these findings into specific design guidelines and protective measures.
Summary updated