Experimental and Numerical Analysis of Mold Filling in Rotational Molding

Jonas Nieschlag, Julian Seuffert, Daniel Strack, Marco Friedmann, Luise Kärger, Frank Henning, Jürgen FleischerJournal of Composites Science 2021 · DOI

TL;DR

This paper presents a novel numerical model for simulating mold filling in rotational molding, a process crucial for creating lightweight composite components. By extending existing RTM simulation techniques and incorporating experimental validation with a custom wireless sensor setup, the authors demonstrate a reliable tool for predicting impregnation progress and optimizing manufacturing.

What Problem Does This Paper Address?

Rotational molding is an attractive process for manufacturing complex, rotationally symmetric composite parts, especially those requiring integrated metallic components. However, unlike more established methods like Resin Transfer Molding (RTM), it lacks robust numerical simulation tools. This gap hinders process optimization, leading to potential issues like incomplete impregnation (dry spots) or inefficient cycle times. The challenge lies in accurately modeling the unique physics of rotational molding, particularly the centrifugal forces driving resin flow and the need for process monitoring in a rotating environment.

Methods

The core of this work is the development of a numerical simulation tool for rotational molding using the OpenFOAM software. The authors adapted an existing RTM solver by:

  • Extending Fluid Mechanics: Incorporating Darcy's law to model liquid flow through the porous fiber preform, treating the matrix as a quasi-incompressible liquid and air as a compressible gas.
  • Implementing Rotation: Adding a source term to the momentum equation to account for the centrifugal forces generated by the mold's rotation.
  • Mesh Simplification: Utilizing rotational symmetry and a symmetry plane to reduce computational cost, creating a 2D simulation domain.
  • Material Modeling:
    • Kinetic Model: Employing the Kamal-Sourour model to describe the curing kinetics of the epoxy matrix, fitted to experimental DSC data.
  • Viscosity Model: Using the Castro-Macosko model to capture the time-dependent viscosity of the resin, validated against manufacturer data.
  • Permeability Model: Adapting models (Gebart, Koch) to describe the anisotropic permeability of the fiber preform, considering fiber orientation and volume fraction, with parameters derived from CT scans.
  • Experimental Validation: Developing a wireless measurement system using a capacitive sensor embedded in the mold to detect the arrival of the resin. This system, powered by batteries and communicating via a Raspberry Pi, allows for real-time monitoring without interfering with the rotation.

Datasets

  • Experimental Data: Impregnation times measured using a custom capacitive sensor setup during actual rotational molding experiments under various temperature and rotation speed configurations.
  • Material Property Data:
    • Differential Scanning Calorimetry (DSC) data for the Sicomin SR8500/SZ8525 epoxy system to determine kinetic parameters.
  • Manufacturer datasheet for the Sicomin SR8500/SZ8525 epoxy system to determine viscosity parameters.
  • Computed Tomography (CT) scans of braided glass fiber sleeves to characterize preform permeability.

Key Insights and Ideas

  • Centrifugal Force Dominance: The simulation highlights that centrifugal forces, driven by rotation, are the primary mechanism for resin impregnation in rotational molding, unlike pressure-driven RTM.
  • Radial vs. Axial Impregnation: The model reveals that radial impregnation is very rapid, while axial impregnation is the rate-limiting step, consuming the majority of the process time.
  • Importance of Material Models: Accurate kinetic and viscosity models are critical for predicting cure progression and flow behavior, directly impacting impregnation time and potential for dry spots.
  • Wireless Sensing for Validation: The development of a wireless capacitive sensor system is a significant practical contribution, enabling in-situ monitoring of the impregnation front in a challenging rotating environment.
  • Parameter Sensitivity: Impregnation time is highly sensitive to temperature (affecting viscosity) and rotation speed (affecting centrifugal force), offering avenues for process optimization.

Key Results

  • The developed numerical model, implemented in OpenFOAM, successfully simulates the mold filling process in rotational molding.
  • Experimental validation showed an average deviation of 43.8% between simulated and measured impregnation times, with a maximum deviation of 65.8%. While this might seem high, the authors note that small deviations in experimental parameters (like temperature or rotation speed) can significantly impact the short impregnation times observed at high speeds.
  • The simulation accurately predicted the qualitative trend of impregnation, with experimental mean values falling within the simulated limits for most configurations.
  • The study demonstrated that increasing temperature and rotation speed can significantly reduce impregnation time.

Limitations and Future Work

  • Deviation in Impregnation Time: The authors acknowledge the average deviation of 43.8% and the maximum of 65.8% between simulation and experiment. They attribute some of this to the inherent scatter in experimental parameters and the difficulty in precisely measuring very short impregnation times.
  • Limited Parameter Space for Validation: The experimental validation was conducted for a limited set of configurations.
  • Future Work:
    • Curing Degree and Demolding: The model's ability to predict curing degree can be leveraged to determine optimal demolding times, preventing premature removal of uncured parts or delays due to over-curing.
  • Integration of Other Matrix Systems and Geometries: The modular nature of the model allows for easy integration of different matrix systems, geometries, or preform architectures by adjusting parameters.
  • Further Experimental Validation: Expanding the experimental validation to a wider range of parameters and potentially different sensor technologies could further refine the model's accuracy.

Summary updated

Abstract

This work focuses on the development of a numerical mold filling simulation for the rotational molding process. In the rotational molding process, a dry fiber preform is placed in a mold and impregnated with a thermoset matrix under rotation. Additionally, metallic load introduction elements can be inserted into the mold and joined with co-curing or form-fit, resulting in hybrid drive shafts or tie rods. The numerical model can be used to simulate the impregnation of the preform. Based on the resin transfer molding process, an OpenFOAM solver is extended for the rotational molding process. Permeability, kinetic and curing models are selected and adapted to the materials used. A wireless measurement solution with a capacitive sensor is developed to validate the model. Comparisons between measurements and numerically calculated impregnation times to reach the capacitive sensor with the matrix show good quality of the developed model. The average deviation between calculated result and measured mean values in the experiment is 43.8% the maximum deviation is 65.8% . The model can therefore be used to predict the impregnation progress and the curing state.
BibTeX
@article{nieschlag2021experimental,
  author = {Jonas Nieschlag and Julian Seuffert and Daniel Strack and Marco Friedmann and Luise Kärger and Frank Henning and Jürgen Fleischer},
  title = {{Experimental and Numerical Analysis of Mold Filling in Rotational Molding}},
  journal = {Journal of Composites Science},
  year = {2021},
  doi = {10.3390/jcs5110289},
}

Loading related content...

Figure