Enhanced superconductivity in PbTe-In hybrids

Zuhan Geng, Fangting Chen, Yichun Gao, Lining Yang, Yuhao Wang, Shuai Yang, Shan Zhang, Zonglin Li, Wenyu Song, Jiaye Xu, Zehao Yu, Ruidong Li, Zhaoyu Wang, Xiao Feng, Tiantian Wang, Yunyi Zang, Li Lin, Runan Shang, Qi‐Kun Xue, Ke He, Hao ZhangarXiv 2024 · DOI · arXiv

Abstract

We report the realization of epitaxial indium thin films on PbTe nanowires. The film is continuous and forms an atomically sharp interface with PbTe. Tunneling devices reveal a hard superconducting gap. The gap size, 1.08 to 1.18 meV, is twice as large as bulk indium's ($\sim$ 0.5 meV), due to the presence of PbTe. A similar enhancement is also observed in the critical temperature of In on a PbTe substrate. Subgap peaks appear at finite magnetic fields. The effective $g$-factor (15-45) is notably enhanced compared to bare PbTe wires ($< 10$) due to the presence of In, differing from Al-hybrids. Josephson devices exhibit gate-tunable supercurrents. The PbTe-In hybrid enhances the properties of both, the superconductivity of In and g-factors of PbTe, and thus may enable exotic phases of matter such as topological superconductivity.

Introduction

The development of topological quantum computers requires materials that integrate the tunability of semiconductors with the quantum coherence of superconductors. For over a decade, Aluminum (Al) on Indium Arsenide (InAs) or Indium Antimonide (InSb) has served as the primary platform. However, these hybrids are limited by a small superconducting gap (~0.3 meV) and the tendency of the metal to quench the semiconductor's high $g$-factor. Other materials often suffer from "soft gaps" or poor interface quality. This paper presents a breakthrough: high-quality epitaxial Indium (In) thin films on Lead Telluride (PbTe) nanowires, creating a hybrid where superconductivity is significantly enhanced rather than degraded.

Experimental Approach

The researchers utilized Selective Area Epitaxy to grow PbTe nanowires, followed by in-situ shadow-wall deposition of Indium thin films (7-10 nm thick). To overcome Indium's tendency to form disconnected grains, two critical steps were implemented:

  1. Cryogenic Growth: The substrate was cooled with liquid nitrogen during deposition to ensure a continuous, smooth film.
  2. In-situ Capping: A 10-nm Cadmium Telluride (CdTe) layer was deposited immediately to prevent oxidation.

The resulting hybrids were characterized using Scanning Transmission Electron Microscopy (STEM) and electronic transport measurements in a dilution refrigerator.

Device architecture, atomic interface, and the observation of a hard superconducting gap in PbTe-In hybrids.

Key Results: The PbTe Boost

A primary finding is the "PbTe Boost"---the unexpected enhancement of Indium's superconducting properties by the PbTe substrate. The superconducting transition temperature ($T_c$) increased from the bulk value of 3.4 K to approximately 6 K. Tunneling spectroscopy revealed a "hard" superconducting gap ($\Delta$) of 1.08–1.18 meV, more than double the bulk Indium value (~0.5 meV) and nearly four times that of Aluminum.

Comparative tests on flat PbTe versus CdTe substrates confirmed that this enhancement is specific to the PbTe interface. The high dielectric constant of PbTe and charge transfer at the atomically sharp interface likely alter the phonon modes or electron-phonon coupling within the thin Indium film.

Comparative resistance measurements showing the enhancement of Tc for Indium films on PbTe substrates versus CdTe.

Synergistic Hybridization

In a rare "win-win" for hybrid materials, the PbTe-In system also enhances the semiconductor's properties. While metals typically suppress the $g$-factor in hybrids, the effective $g$-factor in this system increased to values between 15 and 45, up from less than 10 in bare PbTe wires. High magnetic sensitivity is crucial for reaching the topological regime at lower, more manageable magnetic fields. Furthermore, Josephson junction devices demonstrated high transparency (~80%) and gate-tunable switching currents up to 400 nA.

Conclusion and Future Outlook

The PbTe-In hybrid platform provides a robust environment for exploring exotic quantum states. While the current study did not find definitive evidence of Majorana zero modes (MZMs), the superior gap size and enhanced $g$-factors provide a more favorable starting point than traditional Al-based systems. Future work will focus on optimizing device geometries and gate-tuning to search for quantized zero-bias conductance peaks, the hallmark of topological superconductivity.

Summary updated

Abstract

We report the realization of epitaxial indium thin films on PbTe nanowires. The film is continuous and forms an atomically sharp interface with PbTe. Tunneling devices reveal a hard superconducting gap. The gap size, 1.08 to 1.18 meV, is twice as large as bulk indium's ($\sim$ 0.5 meV), due to the presence of PbTe. A similar enhancement is also observed in the critical temperature of In on a PbTe substrate. Subgap peaks appear at finite magnetic fields. The effective $g$-factor (15-45) is notably enhanced compared to bare PbTe wires ($&lt;$ 10) due to the presence of In, differing from Al-hybrids. Josephson devices exhibit gate-tunable supercurrents. The PbTe-In hybrid enhances the properties of both, the superconductivity of In and g-factors of PbTe, and thus may enable exotic phases of matter such as topological superconductivity.
BibTeX
@misc{geng2024enhanced,
  author = {Zuhan Geng and Fangting Chen and Yichun Gao and Lining Yang and Yuhao Wang and Shuai Yang and Shan Zhang and Zonglin Li and Wenyu Song and Jiaye Xu and Zehao Yu and Ruidong Li and Zhaoyu Wang and Xiao Feng and Tiantian Wang and Yunyi Zang and Li Lin and Runan Shang and Qi‐Kun Xue and Ke He and Hao Zhang},
  title = {{Enhanced superconductivity in PbTe-In hybrids}},
  year = {2024},
  eprint = {2402.04024},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2402.04024},
}
Figure