TL;DR
This paper investigates how to stop high-speed tungsten heavy alloy (WHA) penetrators using layered ceramic targets. By carefully designing the target's stiffness and material interfaces, the researchers achieved "complete interface defeat," meaning the penetrator was fully stopped and deformed without significantly damaging the ceramic. This work highlights the critical role of target assembly and material properties in achieving effective armor performance.
What Problem Does This Paper Address?
Designing lightweight, high-performance armor is a persistent challenge, especially against threats like long rod penetrators. Ceramics are attractive due to their high hardness and low density, but they are brittle and can be easily damaged. Previous research has shown that the effectiveness of ceramic armor is highly dependent on how the ceramic is confined and configured within a multi-layered structure. The key problem this paper tackles is understanding and optimizing the "interface defeat" mechanism in multi-layered ceramic targets. This mechanism aims to cause the penetrator to deform and flow laterally at an interface, rather than directly penetrating the ceramic. The authors seek to identify the specific material and structural design factors that lead to complete penetrator defeat with minimal damage to the ceramic itself.
Methods
The researchers conducted a series of eight ballistic impact experiments using a 50 mm powder gun. They employed tungsten heavy alloy (WHA) long rod penetrators fired at velocities between 1.5-1.7 km/s. The targets were multi-layered, consisting of a steel cover plate, a graphite layer, a ceramic disk (either Alumina or TiB2), and a steel back plate.
Key experimental techniques included:
- In-situ stress measurements: Embedded manganin/constantan gauges were used to record stress histories at specific interfaces within the target.
- Velocity measurements: A VISAR (Velocity Interferometer System for Any Reflector) was used to measure the free surface velocity of the back plate.
- Post-shot analysis: Recovered target components were examined using optical and scanning electron microscopy to analyze damage mechanisms, fragment distribution, and penetrator deformation.
- Crack analysis: Techniques like stereographic analysis were used to quantify crack surface area per unit volume and characterize microcracking anisotropy.
- Fragment size analysis: A mean intercept length approach was used to determine fragment size distribution.
The study systematically varied several parameters, including cover plate hardness, graphite layer thickness, and the method of assembly (bolted vs. welded interfaces), to understand their impact on ballistic performance and penetrator defeat.
Datasets
Not discussed in the paper. The study relies on experimental data generated from ballistic impact tests.
Key Insights and Ideas
- Interface defeat is crucial: The primary mechanism for stopping WHA penetrators without excessive ceramic damage is causing the penetrator to deform and flow laterally at an interface, rather than directly impacting and fracturing the ceramic.
- Stiffness matters: The overall stiffness of the target assembly, achieved through welding components together, significantly enhances ballistic performance and leads to complete penetrator defeat.
- Cover plate hardness is critical: A high hardness (Rc = 53) for the cover steel plate appears to be a necessary condition for achieving complete interface defeat.
- Epoxy bonds are detrimental: The use of epoxy to embed stress/strain gauges at interfaces can lead to premature ceramic damage due to wave reflections, negatively impacting performance. Targets without these bonds showed better results.
- Ceramic type is less critical than assembly: While TiB2 showed slightly better performance with less damage than Alumina in some configurations, the assembly method and material properties of the confining layers (steel, graphite) played a more dominant role in achieving complete defeat.
- Back plate thickness is important: A minimum back plate thickness (25 mm) is required to prevent excessive bending and wave damage to the ceramic, ensuring sufficient stiffness for effective defeat.
Key Results
- Complete Interface Defeat: Achieved in shots 7-1799 and 7-1800, which featured welded components and a hard cover plate (Rc=53). In these cases, the WHA penetrator was fully defeated with minimal damage to the ceramic.
- Partial Interface Defeat: Observed in shots like 7-1797 and 7-1798, where the penetrator deformed laterally but still penetrated the ceramic. This was associated with lower cover plate hardness and bolted assemblies.
- Influence of Cover Plate Hardness: Target 7-1802 (Rc=30 cover plate) was fully penetrated, while target 7-1803 (Rc=51 cover plate) achieved complete interface defeat, demonstrating the strong influence of cover plate hardness.
- Influence of Back Plate Thickness: Target 7-1804 (19 mm back plate) showed only partial defeat, whereas target 7-1799 (25 mm back plate) achieved complete defeat, suggesting a minimum thickness is needed.
- Damage Mechanisms: Microcracking was identified as the dominant failure mode in the ceramic targets.
Limitations and Future Work
- Complexity of Interrelations: The authors acknowledge the complex interplay between various design parameters (hardness, stiffness, material properties) and suggest that future research should focus on numerical simulations to isolate the effect of each parameter.
- Material Models: The development and validation of accurate material models for ceramics, steels, and penetrators are crucial for reliable computational design of armor systems.
- Scaling Rules: The paper proposes that scaling rules for full-scale applications can be derived by preserving key parameters like plate stiffness, penetrator-to-graphite volume ratios, and material properties. Further work is needed to formalize these rules.
- Experimental Constraints: The use of epoxy for gauge placement, while necessary for in-situ measurements, was found to negatively impact ceramic performance. Future experiments might explore alternative methods for embedding sensors or focus on configurations without them.
Summary updated