Abstract
The rapid growth of the Internet of Things (IoT) has led to a significant increase in the power consumption of wireless devices. Simultaneous Wireless Information and Power Transfer (SWIPT) is a promising solution for the sustainable operation of these devices. This paper investigates energy efficiency (EE) in a SWIPT-based Distributed Antenna System (DAS). By optimizing the transmit power of distributed antenna (DA) ports and the power splitting (PS) ratios at IoT devices, the system coordinates energy harvesting (EH) and information decoding (ID). For single-device scenarios, an optimal closed-form solution is derived using Karush-Kuhn-Tucker (KKT) conditions. For multi-device networks, an efficient suboptimal algorithm is proposed. Simulation results demonstrate that the proposed schemes significantly outperform conventional benchmarks in terms of bits per Joule.
Introduction: The IoT Energy Challenge
As the Internet of Things (IoT) continues to expand, billions of sensors and low-power devices are being deployed in diverse environments. A major bottleneck for this growth is the energy supply; replacing or recharging batteries for massive numbers of devices is often logistically impossible or economically unfeasible.
Simultaneous Wireless Information and Power Transfer (SWIPT) offers a compelling solution by allowing radio frequency (RF) signals to carry both data and energy. However, RF signals suffer from severe path loss over distance. Traditional centralized antenna systems often fail to deliver sufficient power to distant devices. Distributed Antenna Systems (DAS) mitigate this by spreading antenna ports geographically, bringing the power source closer to the end-users.
System Model and Power Splitting
In the studied DAS-SWIPT architecture, multiple DA ports are connected to a central processor via high-speed links. Each IoT device is equipped with a power splitter that divides the received signal into two streams: one for the information decoding (ID) circuit and another for the energy harvesting (EH) circuit.
The core optimization problem is to maximize the Energy Efficiency (EE)—defined as the ratio of the achievable data rate to the total power consumption—subject to constraints on minimum harvested energy and maximum transmit power.
Optimization Methodology
The authors address the non-convex EE maximization problem by categorizing it into two scenarios:
1. Single IoT Device
For a single-device system, the authors leverage Karush-Kuhn-Tucker (KKT) conditions to analyze the problem's structure. They discovered that the optimal solution can be expressed in a closed-form using the Lambert $\omega$ function. This is a significant mathematical breakthrough as it allows for instantaneous calculation of optimal parameters without the need for power-hungry iterative numerical methods, making it ideal for real-time IoT applications.
2. Multiple IoT Devices
In multi-user scenarios using Frequency Division Multiple Access (FDMA), the complexity increases. The authors propose a two-stage suboptimal approach:
- Dinkelbach Method: Transforms the fractional objective function (EE) into an equivalent subtractive form.
- Block Coordinate Descent (BCD): An iterative algorithm that alternates between optimizing transmit power and power-splitting ratios until convergence.
Performance Evaluation
The proposed schemes were evaluated using Monte Carlo simulations. The results highlight several key insights:
- Proximity and Scalability: As the number of DA ports increases, the EE improves because devices are more likely to be near a transmitter, reducing path loss.
- EE vs. SE Trade-off: There is a stark difference between maximizing Spectral Efficiency (SE) and Energy Efficiency (EE). While SE maximization focuses on raw throughput by increasing power, it leads to diminishing returns in EE.
As shown in Figure 3, the proposed optimal scheme maintains a significantly higher EE compared to conventional methods. Notably, the SE maximization scheme performs poorly in terms of EE, losing up to 96% efficiency compared to the proposed optimal approach at higher power constraints.
Conclusion and Future Directions
This research demonstrates that combining DAS with SWIPT can significantly enhance the sustainability of IoT networks. The derivation of a closed-form solution for single-user cases provides a highly efficient tool for practical implementation.
However, some limitations remain for future exploration. The current model assumes a linear energy harvesting circuit, whereas real-world hardware exhibits non-linear saturation effects. Additionally, the assumption of perfect Channel State Information (CSI) and static devices suggests that future work should investigate the impact of channel estimation errors and device mobility on system performance.
Summary updated