Energy and exergy analysis of a novel turbo-compounding system for supercharging and mild hybridization of a gasoline engine

Farhad Salek, Meisam Babaie, Ali Ghodsi, Seyed Vahid Hosseini, Ali ZareJournal of Thermal Analysis and Calorimetry 2020 · DOI

Abstract

As the global automotive industry shifts toward hybridization to improve fuel economy and reduce emissions, waste heat recovery (WHR) systems have emerged as a critical area of research. This paper investigates a novel turbo-compound system integrated with an Air Brayton Cycle (ABC) for a naturally aspirated gasoline engine. Using AVL BOOST software, the system was modeled to include a supercharger that delivers extra air to both the engine and the ABC loop. The engine model was validated against experimental data from a 2.0L engine. Energy and exergy analyses at the engine's rated speed revealed that the proposed turbo-compressor can increase mechanical power by 16% to 18% and recover up to 1.1 kW of electrical power. The system achieved a nearly 1% reduction in Brake Specific Fuel Consumption (BSFC) and a slight improvement in overall energy and exergy efficiencies, despite a 23.8 kPa increase in exhaust backpressure.

Introduction

Internal combustion engines are inherently inefficient, with approximately 40% to 60% of fuel energy lost as waste heat through the exhaust system. While hybridization and engine downsizing are standard industry practices, capturing this lost thermal energy is essential for the next generation of efficient powertrains.

Most current Waste Heat Recovery (WHR) research focuses on the Organic Rankine Cycle (ORC). Although effective, ORCs are often too complex, heavy, and difficult to package within passenger vehicles due to the need for secondary working fluids. This study explores the Air Brayton Cycle (ABC) as a leaner, more integrated alternative for naturally aspirated gasoline engines, which are common in the automotive market but often overlooked in high-efficiency WHR research.

Methodology

The study utilized a dual approach of experimental validation and thermodynamic modeling.

  1. Experimental Baseline: A 2.0L KIA Cerato engine was tested on a Schenck 190 kW dynamometer to collect baseline torque and BSFC data across a range of 1000 to 7000 RPM.
  2. Simulation and Architecture: A digital twin of the engine was developed in AVL BOOST and validated against experimental results with an error margin of less than 5%. The novel architecture features a single turbo-compressor and a throttle valve that splits compressed air between the engine (for supercharging) and the ABC loop (for electrical generation).
  3. Thermodynamic Analysis: Energy and exergy analyses were conducted to map energy flows and identify sites of exergy destruction (irreversibility) using MATLAB.
Experimental engine test rig used to collect baseline data for model validation.

Key Results and Discussion

The integration of the turbo-compounding system yielded significant performance gains at the engine's rated speed of 6000 RPM:

  • Power Enhancement: The mechanical power of the engine increased by 16% to 18% due to the supercharging effect of the turbo-compressor.
  • Electrical Recovery: The ABC turbine successfully generated up to 1.1 kW of additional electrical power from the exhaust energy.
  • Efficiency Gains: The system reduced BSFC by nearly 1% and improved both energy and exergy efficiencies by approximately 1%.
  • Exergy Mapping: The analysis identified the engine block as the primary source of exergy destruction (239 kW), followed by the heat exchanger (9.9 kW). This highlights the heat exchanger as a key component for future optimization.
  • System Trade-offs: The primary penalty for these gains was an increase in exhaust backpressure, which reached approximately 23.8 kPa.

Conclusion

The proposed ABC-based turbo-compounding system provides a simpler and lighter alternative to complex ORC systems for gasoline engine hybridization. By utilizing the engine's intake air as the working fluid, the system achieves simultaneous mechanical boosting and electrical recovery. Future research will focus on optimizing the air-fuel ratio and heat exchanger design, as well as evaluating system performance under the transient conditions typical of real-world driving.

Summary updated

Abstract

Number of hybrid vehicles has increased around the world significantly. Automotive industry is utilizing the hybridization of the powertrain system to achieve better fuel economic and emissions reduction. One of the options recently considered in research for hybridization and downsizing of vehicles is to employ waste heat recovery systems. In this paper, the addition of a turbo-compound system with an air Brayton cycle (ABC) to a naturally aspirated engine was studied in AVL BOOST software. In addition, a supercharger was modeled to charge extra air into the engine and ABC. The engine was first validated against the experimental data prior to turbo-compounding. The energy and exergy analysis was performed to understand the effects of the proposed design at engine rated speed. Results showed that between 16 and 18% increase in engine mechanical power can be achieved by adding turbo-compressor. Furthermore, the recommended ABC system can recover up to 1.1 kW extra electrical power from the engine exhaust energy. The energy and exergy efficiencies were both improved slightly by turbo-compounding and BSFC reduced by nearly 1% with the proposed system. Furthermore, installing the proposed system resulted in increase in backpressure up to approximately 23.8 kPa.
BibTeX
@article{salek2020energy,
  author = {Farhad Salek and Meisam Babaie and Ali Ghodsi and Seyed Vahid Hosseini and Ali Zare},
  title = {{Energy and exergy analysis of a novel turbo-compounding system for supercharging and mild hybridization of a gasoline engine}},
  journal = {Journal of Thermal Analysis and Calorimetry},
  year = {2020},
  doi = {10.1007/s10973-020-10178-z},
}
Figure