Abstract
Surface scattering is a major issue in thin Cu films at reduced scales. The rise in the diffusive scattering due to the surface roughness causes the electrical resistance to increase remarkably. In this paper, graphene, as opposed to Al and Pd, is considered as a liner layer for thin Cu film with low-surface roughness using first principles calculation. The surface roughness is simulated using the nonequilibrium coherent potential approximation combined with the linear muffin-tin orbital formulation. The coherent potential approximation band structure shows that the graphene π-bands is not significantly affected by the surface disorder at the Cu surface and that graphene acts as a parallel path to the electrons. On the other hand, the bands of Cu-Al/Pd around the Fermi level are substantially broadened due to the surface disorder. Moreover, the graphene-coated Cu shows less electrical resistance than Al/Pd-coated Cu for surface disorder $x \lesssim 5\%$ for thin films with 0.245 nm in width, and 1.23 nm in thickness. The enhancement in the transport properties in Cu-Gr is attributed to the weak electronic interaction at the interface. The obtained results suggest that graphene is better than Al and Pd as a liner material for thin Cu films.
Introduction: The Nanoscale Interconnect Challenge
As microelectronics continue to shrink, copper (Cu) interconnects—the "backbone" of modern circuits—face a critical performance bottleneck known as the size effect. When the dimensions of a copper wire drop below 50 nm, its electrical resistivity increases dramatically, often doubling or more. This degradation is primarily driven by surface scattering. At the nanoscale, the high surface-to-volume ratio means that atomic-level roughness and vacancies act as significant barriers, causing electrons to scatter diffusively rather than flowing smoothly. To mitigate this, engineers use liner or capping layers to passivate the surface. This study investigates whether graphene can outperform traditional metal liners like Aluminum (Al) or Palladium (Pd) in preserving conductivity.
Methodology: First-Principles Simulation Framework
The researchers employed a sophisticated computational approach to model these films from "first principles," starting from basic quantum mechanics.
The study utilized the Nonequilibrium Coherent Potential Approximation (NECPA) combined with Density Functional Theory (DFT) and a Linear Muffin-Tin Orbital (LMTO) formulation. This framework allows for the analytical treatment of surface disorder (roughness) without the prohibitive computational cost of massive brute-force atomic models. The simulation modeled a thin Cu film (0.245 nm wide, 1.23 nm thick) with varying degrees of surface disorder ($x = 0\%$ to $25\%$ vacuum/vacancies) coated with Al, Pd, or a single layer of graphene.
Results and Discussion: The "Parallel Path" Advantage
The most significant finding is that graphene provides a "parallel path" for electrons that is remarkably resilient to surface roughness.
- Electronic Stability: Graphene’s $π$-bands, which are responsible for its high conductivity, remain distinct and sharp even when the underlying copper surface is highly disordered (up to 25%). In contrast, the electronic bands of Al and Pd liners hybridize strongly with the copper, causing them to broaden and increase resistance as the copper surface becomes rougher.
- Weak Interaction Strength: The superior performance of graphene is attributed to its weak electronic interaction (physisorption) with the copper surface. This weak coupling prevents the disorder in the copper from "bleeding" into the graphene layer, allowing it to act as a high-efficiency bypass for electrons.
- Transport Performance: For surface disorder levels up to 5%, graphene-coated Cu exhibited significantly lower electrical resistance and higher specular transmission ($T_S$) compared to Al or Pd coatings. This indicates that more electrons preserve their forward momentum despite the surface roughness.
- N-Doping Effect: The study noted a small electron transfer from Cu to graphene (n-doping), which slightly shifts graphene's Fermi level but maintains its linear dispersion (the "Dirac point"), preserving its unique transport properties.
Conclusion and Future Outlook
The study concludes that graphene is a superior liner material for thin Cu films with low surface roughness. However, some limitations remain. The effectiveness of graphene decreases as the film length increases if disorder is high, suggesting it is best suited for short interconnects or extremely smooth films. Additionally, while the physics is promising, the practical manufacturing challenge of growing or transferring high-quality graphene onto copper interconnects at scale remains a hurdle for industry adoption.
Reference: M. Ahmed, E. Li and Y. Li, "Electron Transport in Graphene-Versus Al/Pd-Coated Thin Cu Films With Low-Surface Roughness: A First Principles Study," in IEEE Access, vol. 7, pp. 84858-84865, 2019.
Summary updated