Abstract
Interest in photonic crystal nanocavities is fueled by advances in device performance, particularly in the development of low-threshold laser sources. Effective electrical control of high performance photonic crystal lasers has thus far remained elusive due to the complexities associated with current injection into cavities. A fabrication procedure for electrically pumping photonic crystal membrane devices using a lateral p-i-n junction has been developed and is described in this work. We have demonstrated electrically pumped lasing in our junctions with a threshold of 181 nA at 50K - the lowest threshold ever demonstrated in an electrically pumped laser. At room temperature we find that our devices behave as single-mode light-emitting diodes (LEDs), which when directly modulated, have an ultrafast electrical response up to 10 GHz corresponding to less than 1 fJ/bit energy operation - the lowest for any optical transmitter. In addition, we have demonstrated electrical pumping of photonic crystal nanobeam LEDs, and have built fiber taper coupled electro-optic modulators. Fiber-coupled photodetectors based on two-photon absorption are also demonstrated as well as multiply integrated components that can be independently electrically controlled. The presented electrical injection platform is a major step forward in providing practical low power and integrable devices for on-chip photonics.
Introduction
Photonic crystal (PC) nanocavities represent a critical component for future on-chip optical communication systems due to their ability to confine light in sub-wavelength volumes with high quality (Q) factors. While high-performance PC lasers have been demonstrated using optical pumping, achieving efficient electrical pumping—essential for practical integrated circuits—remains a significant challenge.
Previous attempts at electrical injection typically utilized vertical p-i-n junctions. These designs often required a physical "current post" through the cavity, which degraded optical properties and increased fabrication complexity. Moreover, the extreme thinness of semiconductor membranes often leads to current spreading, resulting in wasted energy and excessive heat. This research introduces a flexible, high-efficiency electrical injection platform based on a lateral p-i-n junction that preserves the integrity of the nanocavity design.
Methods and Fabrication
The core innovation of this work is the transition to a lateral p-i-n junction integrated directly into a 220 nm thick Gallium Arsenide (GaAs) membrane. This geometry is inherently compatible with 2D photonic crystal structures and avoids the need for intrusive vertical supports.
The fabrication process involves several high-precision steps:
- Ion Implantation: Silicon (n-type) and Beryllium (p-type) ions are implanted to create doped regions flanking the nanocavity.
- Precision Alignment: Using electron-beam lithography, the doping layout is aligned with an accuracy of approximately 30 nm, ensuring the intrinsic active region coincides with the peak of the optical mode.
- Isolation and Funneling: Deep isolation trenches are etched to prevent current leakage and funnel carriers directly into the nanocavity.
- Active Medium: Indium Arsenide (InAs) quantum dots (QDs) are embedded within the GaAs membrane to serve as the light-emitting medium, chosen for their low transparency carrier densities.
Experimental characterization utilized Atomic Force Microscopy (AFM) and Scanning Capacitance Microscopy (SCM) to map the physical and electrical topography. Two-dimensional finite element Poisson simulations were employed to optimize current density and carrier distribution.
Key Results and Discussion
The lateral junction platform demonstrated exceptional performance across several device types:
- Record-Low Laser Threshold: At 50K, the device achieved lasing with a threshold of just 181 nA. This represents a three-order-of-magnitude improvement over previous PC lasers and is the lowest threshold reported for any electrically pumped laser to date.
- Ultrafast LED Operation: At room temperature, the device functions as a single-mode LED capable of 10 GHz modulation. This high speed is enabled by the high surface-to-volume ratio of the PC cavity, which facilitates rapid carrier recombination.
- Extreme Energy Efficiency: The 10 GHz operation consumed only 2.5 µW of power, translating to an average energy per bit of 0.25 fJ—significantly lower than conventional optical transmitters.
- Versatile Integration: The team also demonstrated fiber-coupled electro-optic modulators (0.6 fJ/bit switching energy) and photodetectors based on two-photon absorption, all integrated on the same lateral junction platform.
Conclusion and Future Outlook
While this work sets new benchmarks for efficiency and speed, room-temperature lasing remains a target for future development. Current room-temperature operation is limited to LED mode due to moderate Q-factors (1000-2000) and free carrier absorption in the doping regions.
Future research will focus on improving Q-factors through refined etching processes, enhancing thermal management using alternative materials like Indium Phosphide (InP), and developing complex integrated systems. The ability to independently control multiple integrated components on a single chip paves the way for advanced wavelength division multiplexing and ultra-low-power on-chip photonics.
Summary updated