Efficient Cooling Method for a Cu Coil in an Induction Cooker by Using an Insulation Sheet

Jong-Han Kwon, Yoon-Jae Nam, Kijung Shin, Sang Ho LimJournal of Magnetics 2011 · DOI

Abstract

Induction cookers are highly efficient appliances, yet they suffer from thermal management issues where heat from the cooking pot radiates back into the internal electronics. This study investigates the use of a silica aerogel sheet to thermally decouple the induction coil from the heat source. By inserting a 2mm thick insulation sheet, researchers achieved a significant reduction in the copper (Cu) coil's operating temperature while simultaneously increasing the heating rate of the cooking pot. These findings suggest a simple modification that can enhance both the longevity and energy efficiency of modern induction cookers.

Introduction

Induction cooking relies on electromagnetic fields to generate heat directly within a ferromagnetic pot. While this process is inherently efficient, the internal copper coils are subjected to high thermal stress from two primary sources: Joule heating (resistive losses within the coil) and thermal back-flow (heat radiating from the hot cooking pot).

Standard induction cookers utilize cooling fans to mitigate this heat. However, these fans often create an unintended "side effect": they cool the ceramic glass surface and the pot itself, leading to energy waste. To address this, researchers proposed using a silica aerogel sheet—a material known for its exceptionally low thermal conductivity (0.155 W/m·K)—to act as a thermal barrier between the pot and the internal components.

Experimental Methodology

The study utilized a commercial 2.4 kW induction cooker modified with a 2mm silica aerogel sheet. The researchers explored two primary configurations to determine the optimal placement of the insulator:

  • Type A: The insulator is placed directly beneath the ceramic glass surface.
  • Type B: The insulator is placed immediately above the induction heating coil.
Schematic of the experimental setup and the two tested configurations (Type A and Type B) for the insulation sheet placement.

Temperature measurements were taken at eight distinct locations on the coil using thermocouples. To simulate various cooking conditions, the team conducted tests using both water (to observe saturation at 100°C) and soybean oil (to observe high-temperature performance up to 260°C).

Results and Analysis

The experimental results demonstrated that Type A was the superior configuration. By placing the insulator directly under the glass, the cooling fan was able to effectively cool the internal electronics without drawing heat away from the ceramic glass and the cooking pot.

Coil Temperature Reduction

As shown in the data, the insulation sheet provided a dramatic cooling effect on the induction coil. When heating soybean oil for approximately 16 minutes, the peak coil temperature dropped from 170.8°C in the standard setup to 135.2°C with the insulation sheet. Similar results were observed with water; the saturation temperature of the coil was reduced from roughly 107°C to 85°C.

Temperature profiles over time for (a) soybean oil and (b) water, illustrating the significant reduction in coil temperature and increased pot heating rate when using the insulation sheet.

Improved Heating Efficiency

Beyond protecting the coil, the aerogel sheet improved cooking performance. Because less heat was lost to the internal cavity of the cooker, the thermal energy remained concentrated in the pot. In the soybean oil test, the oil reached 256°C within 20 minutes with insulation, compared to only 227°C without it. This indicates that the insulation sheet allows the cooker to reach higher temperatures faster using the same amount of electrical power.

Conclusion

The insertion of a silica aerogel insulation sheet represents a dual-benefit solution for induction cookers. It effectively lowers the operating temperature of the induction coil, which is critical for preventing component degradation and ensuring long-term reliability. Simultaneously, it increases the heating rate of the cooking vessel by preventing the cooling fan from dissipating useful thermal energy. Future work should focus on the long-term durability of aerogel materials in these high-stress environments and the economic feasibility of integrating such materials into mass-market appliances.

Summary updated

Abstract

A silica aerogel sheet with a very low thermal conductivity is used to suppress the temperature increase of the Cu coil in an induction cooker by reducing the heat flow from the heat source (cooking pot). It is found that the temperature of the Cu coil is reduced significantly by the insertion of an insulation sheet between the heat source and the Cu coil, demonstrating the effectiveness of the insulation sheet in the suppression of the heat flow between the cooking pot and the coil. Furthermore, the temperature of the cooking pot increases more rapidly with the use of the insulation sheet, allowing for an increased efficiency of the induction cooker.
BibTeX
@article{kwon2011efficient,
  author = {Jong-Han Kwon and Yoon-Jae Nam and Kijung Shin and Sang Ho Lim},
  title = {{Efficient Cooling Method for a Cu Coil in an Induction Cooker by Using an Insulation Sheet}},
  journal = {Journal of Magnetics},
  year = {2011},
  doi = {10.4283/jmag.2011.16.1.031},
}
Figure