TL;DR
This paper tackles a critical challenge in Double-Sided Incremental Forming (DSIF): maintaining consistent tool contact with the sheet metal to prevent premature fracture and improve formability. They introduce a novel toolpath correction model that accounts for in-plane curvature and tool direction, going beyond traditional thickness prediction methods. This leads to significantly improved part quality and the ability to form more complex geometries.
What Problem Does This Paper Address?
Double-Sided Incremental Forming (DSIF) is a promising manufacturing technique for creating complex, freeform sheet metal parts without traditional dies. It uses two tools, one above and one below the sheet, to deform the material. While DSIF offers better control and formability than its single-sided counterpart (SPIF), a key challenge is ensuring both tools maintain continuous contact with the sheet. Loss of contact, particularly with the supporting tool, can lead to localized thinning, premature fracture, and ultimately, part failure. Existing methods for predicting sheet thinning, like the "Sine Law," primarily rely on the local wall angle and are insufficient for complex geometries where in-plane curvature and tool motion also play significant roles. This paper aims to address this gap by developing a more sophisticated toolpath strategy that accounts for these additional geometric factors to guarantee tool contact.
Methods
The authors propose a novel toolpath correction model for DSIF. Their approach involves:
- Defining Geometric Features: They categorize local regions of the part based on in-plane curvature (inward/outward) and tool motion relative to the part's contour (approaching/departing). This is visualized using a "Shamrock" geometry, specifically designed to decouple wall angle from in-plane curvature.
- Developing a Correction Function: A new function,
f, is introduced to modify the tool gap. This function is dependent on feature height, local curvature (p), and the angleβrelated to tool motion direction. The equation is:f = 1 + a₁ (h) [α₂(p) + a₃ (β)]. Whenf=1, the equation reverts to the conventional Sine Law. - Finite Element Analysis (FEA): LS-DYNA software is used to simulate the DSIF process with both the baseline (Sine Law) and the compensated toolpath. This helps to verify the theoretical predictions and understand the mechanics of contact loss.
- Experimental Validation: A custom-built DSIF machine is used to fabricate parts using both the baseline and compensated toolpaths. Strain measurements using laser-marked grids and thickness distribution analysis are performed to compare the outcomes.
Datasets
Not discussed in the paper. The study relies on simulations and experimental fabrication of custom "Shamrock" and truncated pyramid geometries.
Key Insights and Ideas
- In-plane curvature is crucial: The paper strongly demonstrates that simply considering wall angle is insufficient for predicting sheet thinning and tool contact loss in DSIF. In-plane curvature significantly influences where contact is lost.
- Tool motion direction matters: The direction in which the tool moves relative to the part's contour (approaching vs. departing) also affects tool contact.
- Maintaining contact prevents fracture: The core hypothesis, that maintaining tool contact (especially with the supporting tool) delays fracture and improves formability, is experimentally validated. This is attributed to the through-the-thickness pressure provided by the supporting tool.
- "Shamrock" geometry as a testbed: The introduction of the "Shamrock" part is a clever way to isolate the effect of in-plane curvature from wall angle, allowing for targeted analysis.
Key Results
- Simulation: FEA simulations showed that the baseline toolpath (Sine Law) resulted in tool contact loss in specific regions of the Shamrock part, particularly in the "inward/approaching" areas. The compensated toolpath significantly reduced or eliminated this contact loss.
- Experimental:
- The compensated toolpath successfully formed the Shamrock part with significantly improved contact maintenance compared to the baseline.
- When forming a more complex geometry (Shamrock with a 65° wall angle), the baseline toolpath led to fracture, while the compensated toolpath allowed for successful forming without fracture, demonstrating increased material formability.
- Thickness distribution analysis showed more uniform thinning in the compensated parts, with less severe localized necking at corners where contact was maintained.
Limitations and Future Work
- Limitations:
- The paper acknowledges that in the "inward/approaching" region of the Shamrock part, the correction values in the compensated toolpath were "slightly too small," leading to some minor loss of contact.
- The proposed correction function
fuses empirically determined coefficients (a₁,a₂,a₃) based on observations. - Future Work:
- Generalizing the correction algorithm to be applicable to a wider range of part geometries.
- Investigating the local mechanics of DSIF, particularly the stabilization of plastic flow and the potential use of force control to maintain contact.
Summary updated