Effect of Reinforcing Bar on Rayleigh Wave Propagation on Concrete Structures

Jae‐Hong Kim, Kangwook LeeJournal of the Korean Recycled Construction Resources Institute 2015 · DOI

Abstract: This paper presents results on a study of the Rayleigh wave scattering in concrete with a steel bar using transient elastic waves. To study the characteristics of the scattered waves induced by a steel bar in concrete, a three-dimensional finite element method was adopted. A case for elastic wave propagation parallel to the steel bar is discussed. The effect of the cover thickness and steel bar diameter on the Rayleigh wave was studied. To confirm the numerical investigations, a concrete specimen containing a steel bar was made, and corresponding transient elastic wave experiments were conducted. It is believed that the result of this study can serve as an important reference in a nondestructive evaluation of concrete with a steel bar.

Introduction

Nondestructive evaluation (NDE) is essential for assessing the health of civil infrastructure. Engineers frequently utilize ultrasonic pulses or Rayleigh waves to determine the strength and integrity of concrete structures without invasive coring. However, real-world concrete is rarely a homogeneous medium; it is typically reinforced with steel bars (rebar).

When a Rayleigh wave travels along the surface, it penetrates to a depth proportional to its wavelength. If it encounters an embedded steel bar, the wave scatters, leading to complex reflections and refractions. This interference can obscure the concrete's intrinsic elastic properties. This study quantifies how rebar depth (cover thickness) and diameter alter the surface wave signal, providing a framework for more accurate NDE data interpretation in reinforced structures.

Schematic of Rayleigh wave scattering and reflection paths in reinforced concrete.

Methodology

The research employed a dual approach combining numerical simulation and physical experimentation.

3D Finite Element Modeling (FEM)

Using ABAQUS, a 3D model of a concrete half-space was constructed. An impact source, modeled as a half-sine square function to mimic a physical strike, was applied to the surface. A steel bar was placed at varying depths, and the simulation focused on waves propagating parallel to the bar's axis. The study analyzed the tangential components of displacement, velocity, and acceleration.

Experimental Validation

To validate the digital model, a 200x200x600 mm concrete specimen was cast with a 19mm diameter steel bar embedded at a 30mm depth. The concrete mix had a compressive strength of 32 MPa and a static modulus of 31 GPa. Surface wave responses were captured using accelerometers and a signal conditioner for comparison with FEM results.

Parameters

  • Simulation Variables: Cover thicknesses ($c$) of 20, 40, 60, and 80 mm; bar diameters of 10, 16, and 22 mm (D10, D16, D22).
  • Material Properties: Steel (Density: 7,850 kg/m³, $V_p$: 5,920 m/s) and Concrete (Density: 2,380 kg/m³, $V_p$: 4,220 m/s).

Results and Discussion

The primary finding of this study is the emergence of an "oscillatory tail" in the presence of rebar. In plain concrete, a Rayleigh wave signal decays rapidly after the initial pulse. However, the presence of steel reinforcement creates a distinct ringing effect that persists long after the primary wave has passed.

Comparison of surface displacement over time for plain concrete and concrete with a 40mm cover rebar.

Key Insights

  • Depth Threshold: The rebar's influence is inversely proportional to cover thickness. As the cover depth increases beyond the Rayleigh wavelength, the rebar's signature diminishes. At 80mm cover, the signal nearly mirrors that of plain concrete.
  • Diameter and Duration: While both depth and diameter affect the signal, the bar's diameter has a more pronounced impact on the duration of the oscillation. Larger bars (e.g., D22) cause significantly longer ringing than smaller bars (D10).
  • Wave Speed Disparity: Due to the higher wave velocity in steel compared to concrete, refracted waves from the rebar can arrive at the receiver earlier than direct longitudinal waves in the concrete, complicating signal analysis.

The FEM model showed excellent agreement with experimental data, particularly for the first three peaks of the wave signal. The researchers noted that the relationship between bar diameter and signal amplitude was more linear and predictable in simulations than the trends observed for cover thickness.

Conclusion

This study demonstrates that embedded rebar significantly alters Rayleigh wave propagation, primarily through the creation of long-duration oscillatory tails. While this research focused on propagation parallel to the rebar, real-world scenarios involving perpendicular or angled grids will likely produce even more complex scattering.

Future work could investigate how multiple reinforcement layers or varying bond conditions (e.g., corrosion or delamination) affect these signatures. Such research could potentially transform this "interference" into a diagnostic tool for detecting internal structural defects like rebar corrosion.

Summary updated

Abstract

This paper presents results on a study of the Rayleigh wave scattering in concrete with a steel bar using transient elastic waves. To study the characteristics of the scattered waves induced by a steel bar in concrete, a three-dimensional finite element method was adopted. A case for elastic wave propagation parallel to the steel bar is discussed. The effect of the cover thickness and steel bar diameter on the Rayleigh wave was studied. To confirm the numerical investigations, a concrete specimen containing a steel bar was made, and corresponding transient elastic wave experiments were conducted. It is believed that the result of this study can serve as an important reference in a nondestructive evaluation of concrete with a steel bar.
BibTeX
@article{kim2015effect,
  author = {Jae‐Hong Kim and Kangwook Lee},
  title = {{Effect of Reinforcing Bar on Rayleigh Wave Propagation on Concrete Structures}},
  journal = {Journal of the Korean Recycled Construction Resources Institute},
  year = {2015},
  doi = {10.14190/jrcr.2015.3.2.159},
}
Figure